2
RII
x
,WLVXSWRWKHLQVWDOOHUZKRVHUHVSRQVLELOLW\LVWRVHWXSD
GHWHFWLRQ V\VWHP LQ FRPSOLDQFH ZLWK WKH H[LVWLQJ
VWDQGDUGV ERWK (XURSHDQ DQG 1DWLRQDO WR FKRRVH WKH
SURSHUW\SHRIORDGVWRFRQQHFWWRWKHFHQWUDOXQLWDVZHOO
DV WKH FRUUHFW FRQILJXUDWLRQ RI WKH V\VWHP SDUDPHWHUV ,Q
FDVHRIGRXEWVSOHDVHFRQWDFWWKHGLVWULEXWRU
>E@$'-8670(17
In order to get access to the parameters configuration menu a
password is required. The factory-set password value is
’
’
.
It is mandatory to modify it to prevent changes on settings from
unauthorized people, as required by the performance standards.
D
127(
x
,Q HDFK RI WKH IROORZLQJ GLUHFWLRQV DIWHU KDYLQJ VHW D
SDUDPHWHU
3UHVVLQJ WKH HQWHU NH\ VWRUHV WKH FKDQJHV LQWR GHYLFH
PHPRU\
3UHVVLQJ WKH UHVHW NH\ TXLWV WKH FKDQJHV ZLWKRXW
VWRULQJ WKH FKDQJHV DQG UHWXUQV WR WKH XSSHU OHYHO
PHQX
x
,Q HYHU\ SDUDPHWHUV FRQILJXUDWLRQ SKDVH WKH FHQWUDO XQLW
UHWXUQVWRWKHPDLQPHQXZKHQHYHUQRDFWLYLW\LVPDGHRQ
WKHNH\VIRUPRUHWKDQVHFRQGV
3RZHURQVHTXHQFH
32:(521
Ø
),50:$5(
This screen shows the current
9(56,21QQQQQQ
firmware version
Ø
*B&SB
enter
(QWHUSZG
*B0B ! UVW!HQW
Ø
press ’
UHVHW
’ The following screens show the
for 3 seconds last event in each zone
Ø
=RQHSUHDODUP
Pressing ’<’ or ’>’ cycles
through all zones
Ø
=RQHSUHDODUP
Ø
=RQHSUHDODUP
Ø
=RQHSUHDODUP
&RQILJXUDWLRQPHQXV
From the main screen, showing the current state of all active
zones, the user can access all configuration sub-menus which
allow to change the settings of the available parameters for a
proper operation of the gas detection system.
*B&SB
Main screen (example)
*B0B
Ø
press ’enter’
Ø
Pressing ’<’ or ’>’ cycles
(QWHUSZG
through single digits
UVW!HQW
Pressing ’+’ or ’-’ sets the
desired value for each digit
Ø
enter password
Ø
press ’enter’
Ø
=RQHPDQDJHPHQW
Pressing ’<’ or ’>’ cycles
UVW!HQW
through all submenus. Press
’enter’ to access the submenu
Ø
=RQHPDQDJHPHQW
UVW!HQW
Ø
=RQHPDQDJHPHQW
UVW!HQW
Ø
=RQHPDQDJHPHQW
UVW!HQW
Ø
$X[UHOD\PJPW
Auxiliary relay manag. screen
UVW!HQW
Ø
&KDQJHGDWHWLPH
Date/time settings screen
UVW!HQW
Ø
&KDQJHSDVVZRUG
Change password screen
UVW!HQW
(Zone1 management)
=RQHJDVW\SH
Sets the gas type for the sensor wired in Zone 1.
=RQHPDQDJHPHQW
UVW!HQW
Ø
press ’enter’
Ø
=RQHW\SH/3*
Pressing ’+’ or ’-’ cycles
UVW!HQW
through gas LPG - CO - MET
x
/3*
: Selected gas is LPG.
x
&2
: Selected gas is Carbon Monoxide.
x
0(7
: Selected gas is Methane.
(Zone1 management)
=RQHDFWLYH
Sets Zone 1 as active or inactive.
=RQHPDQDJHPHQW
UVW!HQW
Ø
press ’enter’, then ’>’
Ø
=RQHDFWLYH<
Pressing ’+’ or ’-’ cycles
UVW!HQW
through ’Y’ and ’N’
x
<
: Zone is active, i.e. a transmitter is connected.
x
1
: Zone is inactive.
(
Zone1 management)
=RQH/(/SSPDWIXOOVFDOH
Sets the full scale range for the sensor connected to Zone 1. The
value that must be entered here is the full scale value (in % LEL
for combustible or ppm for toxic) that the 4..20mA transmitter
measures when setting its maximum current value, i.e. 20mA.This
allows for the proper indication of the %LEL on the central unit
display. The central unit takes care of converting proportionally all
values between 4 and 20mA into the correct value from 0% (or
0ppm) to the full scale.
R
G
Y
S
00 M
B
P
4
S
E
019179B
0 20041
1
