Seip Solar FR I Installation Instructions Manual Download Page 11

11

Grombacher Straße 83

75045 Walzbachtal-Jöhlingen

Germany

www.seip.com

Walzbachtal, 17.04.2001

EG-Konformitätserklärung

gemäß dem Gesetz über Funkanlagen und

Telekommunikationsendeinrichtungen (FTEG)

und der Richtlinie 1999/5/EG (R&TTE)

EC Declaration of Confirmity

in accordance with the Radio and
Telecommunications Terminal Equipment Act
(FTEG) and Directive 1999/5/EC (R&TTE
Directive)

We,

Wir,

Seip Antriebstechnik

Grombacher Straße 83, 75045 Walzbachtal-Jöhlingen, Deutschland

declare that the product

erklären, daß das Produkt

433 RC AM

Hand-Transmitter as remote-control for garage door operators

Handsender als Fernbedienung für Garagentorantriebe

(Short Range Device)

(Funkgerät geringer Reichweite (SRD))

complies with the essential requirements of §3 and the other relevant provisions of the FTEG (Article 3 of the R&TTE Directive), when used for its intended

purpose.

bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des §3 und den übrigen einschlägigen

Bestimmungen des FTEG (Artikel 3 der R&TTE) entspricht.

§3(1)1, (Article 3(1)a)) does not refer to this type of product.

§3(1)1, Artikel 3(1)a) bezieht sich nicht auf diesen Produkttyp, es gibt hierzu keine Norm

Protection requirement concerning electromagnetic compatibility §3(1)(2), (Article 3(1)(b))

Schutzanforderungen in Bezug auf die elektromagnetische Verträglichkeit §3(1)2, Artikel 3(1)b))

EN 300 220-1/1997

EN 300 683/1997

EN 60950:2000

NSR / Low Voltage Directive 73/23/EEC;93/68/EEC

EMV / EMC Directive 89/336/EEC;92/31/EEC;93/68/EEC

Summary of Contents for Solar FR I













Reviews: