Seiko Astron 3X22 Complete User Manual Download Page 39

Page: 39 / 50

When the watch is unable to receive GPS signals

Points to be checked

When the watch does not start receiving or is unable to receive GPS signals even with

operation of GPS signal reception, the following can be considered.

●

Reception is not started even with operation of GPS signal reception

(time zone adjustment/manual time adjustment).

•

Confirm the energy level and in-flight mode.

Reception is not allowed

Charging status

In-flight mode (

)

Operation

Push Button B and release

Pull out the crown to the first click

Display

When the energy level is “low”, the seconds

hand will indicate the 10-second position.

During in-flight mode (

), the seconds

hand will indicate the 42-second position.

Solution

Charge the watch by exposure to light until

the indicator hand points to the “middle”

position or “full” position.
→ How to charge the watch

P. 14

Reset the in-flight mode (

→ Reset the in-flight mode (

P. 25

●

Reception is not possible even with operation of GPS signal reception

(time zone adjustment/manual time adjustment) (The reception result is

displayed as “N.”)

•

Move to a place where GPS signals can be easily received.

→ Place where GPS signals can be easily received/Place where GPS signals cannot be

received

P. 16

●

The seconds hand stops at the 45-second position before the reception

is completed (The watch enters the power save 2 state)

•

If GPS signal reception is performed under low temperatures (0°C or less) in a state

where the charging capacity and/or charging efficiency are lowered, the reception will

be stopped, and the watch may enter the power save 2 state.

GPS signal reception consumes a significant amount of energy. Keep in mind to charge

the watch regularly by exposure to light.→ How to charge the watch

P. 14

If this occurs frequently, consult the retailer from whom the watch was purchased.

Adjust the time under a condition in which the watch is

unable to receive GPS signals (Manual time setting)

Manual time setting

When a problem cannot be solved even by carrying out the "Points to be checked", or time

is gained or lost under a condition in which the watch is unable to receive GPS signals

and the watch is unable to receive GPS signals continuously, set the time manually.

TROUBLESHOOTING

ASTRON 3X22 GPS SOLAR

Summary of Contents for Astron 3X22



















































Search results

Summary of Contents for Astron 3X22

Reviews:

Seiko Astron 3X22, Complete User Manual, Page: 39 / 50

Search results

Summary of Contents for Astron 3X22

Reviews: