Seiko Astron 3X22 Complete User Manual Download Page 22 | Manualshive

Page: 22 / 50

Seiko Astron 3X22 Complete User Manual Download Page 22

Manual time adjustment

The watch can be set to the correct current time for the set (selected) time difference.

(The time zone will not be changed.)

→ How to manually adjust the time

* The correct time for the set (selected) time difference can be displayed by performing manual time adjustment.

When the region or time zone where the watch is used has changed, perform time zone adjustment. → How to adjust the time zone

(As the time and date will match the set time zone when time zone adjustment is performed, it is not necessary to perform manual time adjustment immediately afterward.)

* DST (daylight saving time or "summer time") is not set automatically. Please perform time difference setting (selection) manually.

→ How to perform manual time difference setting (selection)

* Failure or success of reception depends on the reception environment. → Place where GPS signals can be easily received/Place where GPS signals cannot be received

* At the time when the reception was successful by manually adjusting the time, automatic time adjustment may be performed. For details, refer to "Automatic time adjustment"

* GPS signal reception consumes considerable energy.

Expose the watch to light frequently, and charge the watch so that the energy level is “middle” or “full”.→ How to charge the watch

(If the energy level is “low”, reception will not begin even if GPS signal reception is operated.)

→ Check the charging status

To adjust only the time by GPS signal reception (manual time adjustment)

21

4

BASIC OPERATION (HOW TO SET THE TIME/HOW TO RECEIVE GPS SIGNALS, ETC.)

ASTRON 3X22 GPS SOLAR

«
...
20
21
22
23
24
...
»

Summary of Contents for Astron 3X22



















































Reviews:

No comments