background image

[SPECIFICATION]

3 Hands (Hour, minute and second hand)

Movement size

Diameter

Outside 

 

φ

27.4 mm

Calendar (Date: Date disk)

Casing

 :

 

φ

27.0 mm

Height

 

  

  

 

 

 : 

5.25 mm

Driving system

 

 Automatic winding with manual winding mechanism

PARTS LIST / TECHNICAL GUIDE

Cal.6R15A / 6R15B

Cal. No.

6R15A / 6R15B

Item

 

Date setting (counter closkwise only)

 2nd click position

 

Time setting / Second hand stop function

Loss/
Gain

 Daily rate

 

B25/-15 seconds per day

 

(worn on the wrist at temperature-range between 5

 and 35

)

 Standard rate for
 measurement

6 o’clock at

the top

9 o’clock at

the top

Dial upward

Measurement (daily
rate in seconds:s/d)

±10 s/d

±15 s/d

Additional function

 ・

Instant date setting device

 ・

Second hand stop function

Crown

position

 Normal position

 

Manual winding (clockwise only)

 1st click position

Vibrations per hour

 

21,600 (6 beats per second)

 

ETACHRON system

Instantaneous rate at T0

(Fully wound condition)

Isochronous fault

Testing positions

Dial upward

Number of Jewels

±15 s/d

±

10 s/d

1/16

Lift angle of the escapement

 

53°

Continuous operating time

 

From fully wound to stoppage: Approximately 50 hours

 

23 Jewels

Regulation system

Summary of Contents for 6R15A

















Reviews: