Segway NEB1002-H1, User Manual

Page: 2 / 18

4 Safety Instructions
1. Battery model NEB1002-H1 is only suitable for the Ninebot KickScooter ES, E22, E45
series models. Battery model NEB1002-U1 is only suitable for the Ninebot KickScooter
E25 series. Do not use other models or brands of scooters, otherwise there may be
safety risks.
2. Do not store or charge the battery at temperatures outside the stated limits (see
Specifications).
3. Do not touch battery contacts. Do not dismantle or puncture the casing. Keep the
battery contacts away from metal objects to prevent short circuit.
4. Risk of fire. Do not expose the battery to fire.
5. Do not charge or use your battery if it is damaged or see trace of water.
6. Do not puncture the battery. Do not attempt to disassemble the battery. No user
serviceable parts.
7. Completely draining the battery may cause permanent damage to the battery. Charge
the battery after each ride and avoid draining the battery completely. Please read the
user manual before charging the battery.
8. Do not discard or destroy the battery. Refer your local laws and regulations regarding
battery recycling and/or disposal.
5 Specifications
ES Series: ES1, ES2, ES2L, ES4
E22 Series: E22, E22D, E22E
E45 Series: E45, E45D, E45E
E25 Series: E25, E25A,
E25D, E25E
184 Wh
NEB1002-H1
5100 mAh
32—104°F (0—40
℃
)
215 Wh
NEB1002-U1
5960 mAh
36 V
42 V 36 V
42 V
Ninebot KickScooter External Battery
Max. Charging Voltage
Nominal Energy
Nominal Capacity
Storage Temperature
Battery Management
System
Suitable for Ninebot
KickScooter model
Nominal Voltage
Model
Black
Gray Color
Name
Over-heating, short circuit, over-current,
over-discharge and over-charge protection
3 Charging
Charge port
Steps:
①
Open the charge
port cover.
③
Close the charge
port cover when
finished.
②
Insert the
charge plug.
Your KickScooter is fully charged when the LED on the charger changes from red (charging)
to green (trickle charge). Close the charge port cover when not charging.
Do not connect the charger if the charge port or charge cable is wet. Do not charge or use
your battery if it is damaged or see trace of water.
1. Remove the cover (a), and remove the M3
screws (b) with 2.5 mm hex wrench . Then
remove other components (c).
2. Remove the screw (d) with 2 mm hex
wrench. Then remove the three screws
(e) on the stem with 2.5 mm hex wrench.
3. Align the rail. Pre-tighten the screws in
order with 2.5 mm hex wrench and tighten.
4. Install the external battery on the rail.
Fixate the two M4 screws (with 3 mm
hex wrench) and the M3 screw (with 2.5
mm hex wrench). Block the screw holes
with the rubber stopper when installed.
2 Installing
1 Packing List
User Manual Battery Pack
Rail
Accessories
When unboxing your battery pack, please verify that the above items are included in the package. If any
components are missing, please contact your dealer/distributor or nearest service center.
Power on the KickScooter. Press the Power Button to
turn on/off the ambient light.
* E22D, E25D, E45D does not have this feature.
Rubber Stopper
3 mm
Hex Wrench
2.5 mm
Hex Wrench
2 mm
Hex Wrench
M4 Screw
× 2
M3 Screw
× 1
Ambient Light
User Manual
(d)
(e)
(c) (b) (a)
1
2
3
Pre-tightening
state
M4 Screw
M3 Screw