background image

 

Release Version 1.1 

Precaution and Safety Guidelines   

The content of this guideline is to protect the safety of users and prevent property damage.   
Be sure to read this user’s manual thoroughly and use the device correctly.   

Warning 

(If you do not keep any of the below guidelines, you may get seriously injured or 

cause somebody’s death.) 

  Be sure to install the product after unplugging power cord. Also, do not use several 

power plugs at the same time.   

- It may cause abnormal heat, fire and electric shock.   

■  Do not leave the device at any place that water falls or splashes. Also, do not put anything 
full of water such as a flower vase on the device.   

- It may cause malfunction or fire if liquid goes into the device.   

■  Do not bend the power cord by excessive force. Make sure the power cord is not crushed by 
heavy things.   

- It may cause fire.   

■  Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble, 
repair or modify it.   

- By abnormal working, it may cause fire, electric shock and personal injury.   

■  Do not install this product in places with high humidity, dust, or soot.   

- It may cause electric shock and fire.   

■  Do not tug at the power cord section or unplug the power plug with wet hands. If the power 
cord is loose, do not plug in. 

- There may be a risk of fire and electric shock.   

■  Always keep the location of the appliance clean during or after installation to prevent dust. 
Especially when cleaning the device, wipe it with dry towel and do not use water, thinner or 
organic solvent.   

- It may damage the case of this device, and cause malfunction or electric shock.   

■  Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper 
temperature and avoid heating appliances like candle or heater. Also, keep the equipment or 
tools away from places where people come and go.   

- It may cause fire

■  Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power 
extension cables, old power cords and a lack of safety earth. Consult your place of purchase or 
professional if problems arise.   

- It may cause fire and electric shock. 

■  Concerning the input voltage for operating this device, a voltage range must be within 10% 
of rated voltage, and the power outlet must be grounded. Also, do not use a heat source such 
as a hair dryer, iron and refrigerator to the same power unit.   

- It may cause abnormal heat, fire and electric shock. 
 
 
 

Summary of Contents for SC-IPT07P













Reviews: