Security Tronix ST-CCTV-VBAC-POEPTZ Installation Manual Download Page 2

v2.0  10/16/10 

PACKAGE CONTENTS 

This package contains: 
 

One ST-CCTV-VBACT-POEPTZ Active Video Transmitter 
One ST-CCTV-VBACR-POEPTZ Active Video Receiver 
One installation manual 
 

Note:  A  DC  power  supply  is  required.  Selection  of  a  power  supply  with  the  correct  voltage  and 
ampere rating is determined by the voltage drop for the specific length of UTP cable used between 
the transmitter and receiver. Consult your UTP cable manufacturer’s specifications to determine 
the voltage drop. 

 

 

PRODUCT DESCRIPTION 

 

The  ST-CCTV-VBAC-POEPTZ  Active  Video  Balun  Transceiver  allows  the  transmission  of 
real-time video and power over Unshielded Twisted Pair (UTP).  The ST-CCTV-VBACT-POEPTZ 
video transmitter converts an unbalanced video signal to a balanced signal transmitted over UTP. 
The  ST-CCTV-VBACR-POEPTZ  video  receiver  then  converts  the  balanced  video  signal  to  an 
unbalanced  signal  for  display  on  the  device.  These  units  offer  excellent  common  mode  and 
multi-channel interference rejection and the transmission and display of high quality color video for 
security, surveillance, video conferencing, video distribution and PTZ control signal applications. 

 

The ST-CCTV-VBAC-POEPTZ also transmits electrical power along with data to remote devices 
over standard UTP cable. In applications such as security surveillance and elevator surveillance 
the Power Over Ethernet (POE) feature allows the UTP cable to replace power, video coaxial and 
data  cables  making  system  installations  easier,  faster  and  less  expensive  without  building 
remodeling.  

 

SPECIFICATIONS

 

ST-CCTV-VBAC-POEPTZ

 

Specifications (Typical)  

1.   Video Frequency Response 

DC-6MHz 

2.   Video Common Mode and Differential Mode Rejection 

15KHz-6MHz 60dB typical 

3.   Wire Type 

UTP 
DC Loop Resistance 

18

Ω

/100m 

4.   Interface 

2 PIN UTP Terminal Block 
BNC (female) Connector 
RJ45 Connector 
DC Jack 

5.   Impedance 

Twisted Pair: 100

Ω

 

BNC Coax: 75

Ω

 

6.   Transmission Distance (video only) 

1800 meters / 5,905 feet  

7.   Suppression 

6KV 1.2uSx50uS; 4KV 8uSx30uS 

8.   Power 

RX : 38VDC max. (input); TX : 12VDC (output)  

9.   Environmental 

32° - 122° F, 0%-95% Humidity 

10. Dimensions 

3.2”x.2.3”x1.2” (with BNC) 

11. Weight 

4.6 oz  

 

Summary of Contents for ST-CCTV-VBAC-POEPTZ







Reviews: