How the lights operate
Pulse - 1 second on, 1 second off
Flash - 1/2 second on, 1/2 second off
Rapid Flash - 1/4 second on, 1/4 second off
Wink - 1/4 second on, 1 3/4 seconds off
READY
On when the system is ready to be armed.
Off when the system is armed or a burglary zone is faulted.
Rapid Flash when an alarm has occurred and the system is
disarmed.
TROUBLE Off when the system is operating correctly.
Pulse when the system is unable to send a report to the
supervising panel.
POWER
On when main power is okay.
Off when main power is disconnected.
Pulse during low battery.
ARMED
On when Perimeter or Interior are armed.
Off when Perimeter and Interior are off.
Rapid Flash when an alarm has occurred and the system is
armed.
Pulse during exit delay after you’ve armed the system.
STAY
On when the Perimeter only is armed.
Off when all areas are armed or disarmed.
INSTANT
On when the system is instant armed with no entry delay.
Off when the system is armed with entry/exit delays or is
disarmed.
ZONE
On when the zone is disarmed and faulted.
Off when the zone is normal.
Rapid Flash means a zone alarm. This flashes until the zone is
disarmed and a user code is entered a second time.
Wink when the zone is bypassed.
Pulse when the zone is in a trouble or zone monitor condition.
A
BC
D
E
F
G H I
J K L
VW X
MN O
P
Q
R
STU
Y Z
COMMAND
SPECIAL
STAY
INSTANT
BYPASS
CODE
9
0
1
2
3
4
5
6
7
8
1
2 3 4
INSTANT
STAY
ARMED
TRBL
POWER
READY
Your Security Command Keypad
Arming and Disarming Your System
Arming the system
When the
READY
light is on, enter your own user code in place of
(
your code):
(
your code) or
Arms all areas.
C 1
or
Arms all areas.
STAY
Arms only the Perimeter.
You can press the INSTANT key before starting the arming sequence or
after (while the
READY
light is pulsing) to arm the system without any exit or
entry delays.
You may force arm the system while one of your burglary protection zones
is faulted (front door open). Simply continue to hold the last key press down
for 2 seconds; the keypad will beep once. When the zone returns to a
normal condition (door closes), it becomes part of the armed system again.
Disarming the system
When the
ARMED
light is on, enter:
(
your code)
Disarms all areas. You can enter your code
again to clear any zone alarm memory
(lights that are flashing rapidly).
Disarming during an alarm
When the
ARMED
light is on and a zone is in alarm, enter:
(
your code)
Silences the alarm and disarms the system.
Enter again to clear any zone alarm
memory (lights that are flashing rapidly).
Burglary zone alarm lights clear
automatically after a few minutes.
Easy Exit
This function allows you to exit while the Perimeter is armed.
BYPASS
or
Restarts the exit delay. Perimeter arms at
COMMAND + 9
expiration of the exit delay or at second
press of BYPASS key.
Security Command Functions
Bypassing a Zone
Bypassing means the system ignores events that occur on the zone. You
can bypass a disarmed zone, such as a patio door, so it can be used while
the rest of the Perimeter protection is turned on. Use 2-digit zone numbers;
example: 01, 02, 03. Zone 4 is a 24 hour zone and cannot be manually
bypassed.
(
your code)
+ (zone)
Bypasses the zone.
If already bypassed, the zone will
unbypass.
Resetting Sensors
Use this function to reset smoke detectors after an alarm when the fire zone
light is flashing in alarm memory.
(your code) or
The system resets the smoke detectors and
stops the flashing light if the zone restores
to normal.
Note: Your system may not be configured
for Zone 4 as a Fire zone.
Testing the System
It’s good practice to test your system at least once each week. This assures
you that the system is working correctly and identifies any potential
problems.
COMMAND + 4 + 1
The bell rings and the internal speaker
beeps for 1 second.
Monitoring Zones
You can monitor zones in the system so that the keypad emits a short door
bell tone any time that zone is faulted. Use 2-digit zone numbers; example:
01, 02, 03.
C 6 +
(
your code)
+ (zone)
Monitors this zone only.
C 6 + (
your code) +
STAY
Monitors all Perimeter zones.
C 6 + (
your code) + SPECIALMonitors Perimeter/Interior
zones.
Repeat to remove a zone from
monitor mode.
User Codes
This function allows a user (01-08) to add, change, or delete a user code
from the system.
CODE +
(
your code)
+ # #
+
C C C C
Adds or changes a user code
CODE +
(
your code)
+
# #
+ 0 0 0 0
Deletes a user code
## = 2-digit user number
0 = Enter four zeroes
C
= New user code
NUMBER KEYS
READY
TROUBLE
POWER
BUILT-IN ALERT
SPECIAL KEY
COMMAND KEY
STAY
INSTANT
FUNCTION KEYS
ZONES 1 TO 4
ARMED
How the Alert tone operates
Burglary Siren
A burglary alarm condition on zones 1, 2, or 3.
Fire Siren
A fire alarm condition on zone 4.
Steady Tone
A trouble condition on the system or a fire zone.
Pressing any key silences a steady alert tone.
1 Short Beep
Each time a valid function is entered.
4 Short Beeps
When an incorrect value is entered.
Built-in Alert Operation
COMMAND + 4 + 7
