background image

Subject to modifications

-- page 1 --

SELO-C-Standard-Betriebsanleitung-englisch.p65

Date: 12.06

Operating instructions - Basic functions

of electronic lock SELO-C (Version 1.0)

Fully redundant electronic lock model SELO-C allows you to open the lock after entering the valid 7- or 8-digit secret code. The
maximum number of codes for clearing the lock is 10.

A)   GENERAL

-

The opening procedure consists of two operations: CLEARING and UNBLOCKING.

-

To start the opening procedure, check that the input unit is in the vertical end position.

-

All accepted key strokes will produce a response on the display.

-

If the code number is keyed in by mistake, return to the starting position of the lock by pressing the On/Enter key, and start
over.

-

After entering the wrong secret code three times in a row, the lock will automatically block all further entries for 5 minutes.
If, after waiting for 5 minutes, the wrong code is entered again, the lock will block itself for a further 20 minutes
(manipulation resistance). During this time, the remaining delay is depicted on the display and not even the valid number
code will open the lock.

-

If more than 30 seconds lapse between pressing any two keys, the lock automatically switches itself off for safety reasons.
The opening procedure has to be started over.

-

Once data have been stored (numerical codes, time frame and user entries), not even a power failure will delete them.

-

The lock is of fully redundant design. This means that all electrical components which are crucial to the proper functioning
of the lock come in pairs.  In the unlikely event of the primary system breaking down, the lock can, therefore, always be
opened undamaged using the secondary or backup system.

3 lines for entering codes and
displaying messages

1 line for displaying battery
condition and key functions

Function key for correcting data
input and selecting menu
functions

On/Enter-key to switch on the
unit, select functions and to set
the lock to its starting position

Rotary handle for unblocking

the lock

Multifunction keys „2“ , „4“, „5“,

„6" and „8“ for moving the cursor

and entering the code

Keys „0“ -  „9“ for entering

numbers and plain text

- Battery condition „1/3 full"

- Key marked „Function“ to return

to next higher menu level

- Keys  „1“ and „2“ to navigate

through the menu

- Battery condition „full“

- Key marked „Function“ to select

the desired menu from the
setting mode

- Battery condition „2/3 full"

- Key marked „Function“ for

deleting the figure entered last

- Battery condition „almost empty"

Multifunction keys „1“ and „2“

for entering figures and words,

and for menu navigation

Summary of Contents for SELO-C

Page 1: ...lock automatically switches itself off for safety reasons The opening procedure has to be started over Once data have been stored numerical codes time frame and user entries not even a power failure will delete them Thelockisoffullyredundantdesign Thismeansthatallelectricalcomponentswhicharecrucialtotheproperfunctioning of the lock come in pairs In the unlikely event of the primary system breaking...

Page 2: ...ode entering key 5 once to complete select ing the figure 2 as one of the figures of the secret code Clearing the lock 1 Press On Enter When the lock is ready for operation you will be asked to enter the code eight seconds after the status of the opening counter is displayed You can abort the opening counter indication by pressing any number key 2 Now enter the 7 or 8 digit numerical code factory ...

Page 3: ...er you see the symbol above the key After leaving the setting mode the lock is again ready for clearing The operator is prompted to enter a valid secret code Changing an existing user code 1 Assoonasyouenterthesettingmode thecursorwillautomaticallygotoCodechange Toselect presstheOn Enter key 2 Next the administrator and the various users are depicted on the display with the administrator in first ...

Page 4: ...he warning Backup cde still factory setting whenever it is switched on IMPORTANT SAFETY ISSUE When preparing the lock for operation for the first time change the factory set administrator code 1 2 3 4 5 6 7 of the backup system to the secret code of your choice Failing this the lock can be opened by anybody knowing the factory setting whenever it is in backup mode Opening the lock backup mode 1 Pr...

Reviews: