SECOLink KM24 Short User Manual Download Page 2

Page: 2 / 8

, [

Zone bypass

, ... or , and ,

PIN:

WXYZ

####

ENT

Arming and disarming of security barrier, “Pre-Alarm” mode

Partial arming

, [Pre-Alarm], ... ,

GHI

ENT

PIN:

Bypassing zone

Abort arming

For selection aborting, also arm procedure aborting the system SECOLink has the key. If the exit delay is
in process and you want to abort arming, press the key and enter PIN code.

CLR

Arming system with troubles

01:44

0-26

+25°C

Short user manual

Intruder alarm system

KM2

4, KM24A

keypad

KM2

4, KM24A

keypad

This is universal way of arming, which enables to arm selected partition in desired arming mode.
Example: Only the first partition is armed. This kind of arming is available in

2-storied house

, when at night

the ground

floor isn’t used

, all sensors of this partition are armed. When somebody opens doors will be an

entry delay.

armed

wi ll be

System

Press

key

to select arming

mode

For partial arming press

... keys

GHI

System will be armed.

Press

key.

Away

Press [ENT] to arm
Press[ ] to select mode
Press [1]..[4] to select

part.

Arming

READY TO ARM

01:44

1st Floor

2nd Floor

0-26

+25°C

2 nd Floor

1st Floor

Sritys

Using ... keys check all

partitions which have to be armed.

Press key to confirm the

decision.

GHI

ENT

Zon

Hallway

Kitchen

Bedroom

Smoke detector

Door

Zone isn’t violated

Zone is violated

Zone is bypassed temporary

Zone is bypassed

permanently

Microwave or infrared rays based security barriers, also outdoor PIR detectors, which are connected to the
system, can be armed by “Pre-Alarm” mode. The system will sound an alarm (without sending alarm
message to Central Monitoring Station), when someone traverses this electrical barrier. The “Pre-Alarm”
mode can be turned on and turned off by marking/unmarking partitions with ... keys or by selecting
partitions with , keys and marking/unmarking with , keys.

GHI

####

Bypassing a zone allows you to leave a door or window open while still arming the rest of your security
system. Bypass procedure can be made:

There are two different bypass types: temporal or permanent. First is used for one arming and disarming cycle, second – until
the user unbypass the zone. Enter the zone number you would like to bypass.   THIS   MUST   BE   A   TWO   DIGIT NUMBER
(for the first zone – 01, for second – 02 and so on). The zone will be marked by "x". The last number should be pressed and
held for 2 sec to bypass the zone for a long time (permanently). The zone will be marked by capital "X". When all zones are
marked press the    key. The same actions can be performed by selecting the zones with the keys    or    and by
marking/unmarking   with the    key (short press – temporal zone bypass, long – permanent zone bypass).

ENT

####

EU standards unexpect

using of the system, which has troubles. When key is backlighted with green

color, the arming is impossible in the ways, which were described earlier. It is necessary immediately
eliminate troubles, also inform CMS and company, which had installed the system.
The system detects troubles in own modules, also it detects and other common troubles, like

230V

disappearance in AC line, disconnected phone line because of repair

, battery discharge. In exceptional

cases is possible to bypass the troubles for a short time and arm system as usual.
It can be done this way:

CLR

Press the key once – message about the trouble will be shown on the display. Press the key again –
the key backlight starts to blink fast. The blinking duration is

seconds. During this time

is possible to make

usual arming procedure.

CLR

Sys. Trouble

AC Loss