ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Covert PIR Camera
4
SECO-LARM U.S.A., Inc.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
®
PICVN3
MI_EV-Y6501-A3WQ_200429.docx
The screen is black
Check that the camera is powered up
Check that the power supply’s polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to the
monitor is connected properly
The image is foggy or washed out
at night
Check that there are no objects very close to the camera
Check that there are no highly reflective objects in the scene
The screen image is dim
Clean the lens using a soft, clean cloth
Check that the light source is adequate
The screen image has poor contrast
Adjust the monitor’s contrast knob
Change the position of the camera
The screen image flickers
Change the position of the camera, check cables and
format setting
The screen image is distorted
Change the position of the camera, check cables and
format setting
The camera case is hot
Check that the correct power supply is in use
IR LEDs do not turn on
Check that the correct power supply is in use
Troubleshooting:
WARNING:
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no user-serviceable components inside.
Do not cut any wires as the warranty will be voided.
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws
and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be held responsible for the use of this product
in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.
Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to
operate the device.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three
(3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part
if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God,
physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other
reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of
SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All rights reserved.
