ENFORCER B
ALL
-M
OUNT
IR D
OME
C
AMERA
Manual
ENFORCER B
ALL
-M
OUNT
IR D
OME
C
AMERA
Manual
Dimensions:
To BNC
(From DC
Camera)
(EVA-F5521-3)
(3-ft. wire length)
EVA-F5521-3 -- Optional power cord. For easy
connection of dome or bullet camera to power supply.
3
11
/
16
” (93mm)
Parts List
1 x Camera Ball
1 x Case (2-part construction)
1 x Base
3 x Screws
1 x Manual
BEFORE STARTING
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*
INSTALLATION
1. Run a 12VDC power supply wire and a video cable with a male
BNC connector through the wall to where the camera is to be
mounted.
2. Temporarily connect the camera to the 12VDC power supply.
3. Temporarily connect the camera’s female BNC connector to the
video cable’s male BNC connector.
4. While watching the monitor, hold the camera against the wall
by hand where it is to be mounted, then turn the camera until it
is certain that this mounting location is correct. Use a pencil to
mark the location of the three screw holes in the base.
5. Disconnect the 12VDC power supply and video cable.
6. Do not open or disassemble the camera. There are no user-
serviceable parts inside.
7. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic
fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.
6. Mount the bracket to the wall using the three included mounting
screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use screw anchors (not included).
7. Reconnect the 12VDC power supply and video cable. Turn the
monitor on, and make sure the camera is sending the proper
video signal.
8. Adjust the camera angle.
9. Put the case over the camera ball and twist to secure to the
base.
10. Do a final test of the video camera and monitor.
* Note: The base also allows flush-mounting of the camera.
However, for the best security, run the wires through the wall.
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
IR LEDs
IR distance
IR view angle
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Automatic gain control
White balance
Power source
Power consumption
Storage temperature
Operating temperature
Dimensions
Weight
EV-122C-DXA3 (NTSC)
Color camera
1/3” CCD, Sony
420 TV lines
510 x 492 pixels
2:1 interlace, V: 59.94Hz, H: 15.734KHz
Internal
1V pp composite output, 75 ohms
F1.2, 3.6mm (lens included)
24 x LEDs
Up to 50’ (15m)
50
o
~80
o
beam spread, 30
o
per LED
0.05 lux, (0 lux with IR on)
0.45
>50dB
Auto Electronic Shutter (AES), 1/60~1/100,000 sec.
Auto
Auto
Auto, 2500
o
~ 9500
o
K
12VDC ±10%
70mA (IR off), 280mA (IR on)
-22°~140° F (-30°~60° C)
14°~122° F (-10°~50° C)
3
11
/
16
” x 2
11
/
16
” (93 x 69mm)
6.3 oz. (180g)
Specifications
2
11
/
16
”
(69mm)
Case
Case
Camera
Ball
Base
3 x
Screws
Power
Connector
BNC
Connector