ENFORCER RF R
ECEIVERS
ENFORCER RF R
ECEIVERS
Learning a New Button Code (channel 1)
1. Press the mode switch which is located at the top of the receiver case for three seconds. The green LED will start to
flash quickly.
2. While the green LED is flashing quickly, press a button on a compatible transmitter. The green LED will flash once
and then turn off to show that button was learned.
3. Repeat steps 1 and 2 to learn more buttons into channel 1.
NOTE — The green LED will flash a maximum of 15 seconds. If no transmitter button is pressed during this time, the
receiver will exit the code-learning mode, and the green LED will turn off.
Learning a New Button Code (channel 2, SK-910RAV2Q only)
The procedure is the same as for channel 1, except mode switch #2 (black switch) initiates the code-learning process,
and the red LED shows status. For two channel receivers,
red
color push-button represent mode switch #1 and
black
color push-button represent mode switch #2 .
Note Regarding Code Learning
1. The receiver will only learn the code of a particular button once. Once a button’s code is learned, if you try to code-
learn that button again, whether it is for the same channel or not, the receiver will remain in the code learning mode.
The LED will turn steady ON (1-sec.) to show the code is already in memory.
2. Each channel can learn the codes of a maximum of 15 transmitter buttons. If you attempt to learn a sixteenth
button, the earliest code learned will be deleted and replaced by the new code (first-in, first out).
3.
To clear all codes
— To clear all codes in the channel’s memory, press the appropriate mode switch (#1 or #2)
for three seconds. When the LED starts flashing, press that switch again for three seconds. The LED flashes twice to
indicate that all codes associated with that channel are now deleted.
Learn mode
Clear memory
Memory Display
Steady on
Fast flash
One flash
Two flashes
Press and hold the switch for three seconds. The appropriate LED will flash quickly to show that it
is ready to learn a transmitter code.
Press three seconds, then when the appropriate LED starts flashing, press again for three seconds
to delete all previously learned codes. The LED will flash twice to confirm codes deleted.
Press and immediately release the mode switch to show number of codes stored. The appropriate
LED will flash a number of times to correspond to the number of codes stored.
Senses signal from a transmitter button whose code was already learned.
In the code-learning mode.
A transmitter button code was learned.
All previously learned transmitter button codes were deleted.
Mode Switch Operation (one per channel)
LED Indication (one per channel)
4-second momentary
1-second momentary
Toggle
Validity
Press the transmitter button once. The output turns on for 4 seconds, and then turns off.
(This is the DEFAULT mode)
Press the transmitter button once. The output turns on for 1 second, and then turns off.
Press the transmitter button once, and the output turns on. Press a compatible transmitter
button again, and the output turns off.
The relay turns on for as long as the transmitter button is pressed.
Programming Output Modes (see table 1)
Extended Range Antenna for SK-910RAQ only
The optional
SK-91ERSD
extends the RF receiver range to up to 1,200’ (open air) with existing remotes.
The antenna comes with a 9’ cable which easily plugs into the 3-pin antenna port located on the RF receiver motherboard
(see the illustration above).
SK-91ERSD
IMPORTANT:
If an extended range antenna is used with the
SK-910RAQ, the receiver PC board loop marked “LP3” must be cut.
Mode switch #1
SK-910RAQ
Mode switch #1
Mode switch #2
(SK-910RAV2Q only)
SK-910RAVQ/RAV2Q
11~24 VAC/VDC
No polarity
COM
NO
NC
{
3~13.8 VDC
GND
Ch 1 transistor ground
Ch 2 transistor ground
(SK-910RAV2Q only)
Table 1:
To program outputs,
open case and find the
jumpers marked LP1, LP2,
LP3, and LP4 . Cut these
jumpers, if needed, as
follows:
NOTE — For the SK-910RAV2Q
2-channel model, the mode of
both outputs is the same. In
other words, you cannot have
4-second momentary output
for channel 1 and a validity
output for channel 2.
Channel 1 Status LED
Channel 2
Status LED
(SK-910RAV2Q only)
UNCUT UNCUT CUT CUT
UNCUT CUT UNCUT CUT
LP1
LP2
LP3
LP4
4-SEC.
MOMENTARY
TOGGLE
VALIDITY
1-SEC.
MOMENTARY
CUT LP4 FOR 16~24VAC/DC POWER INPUT (for SK-910RAQ only)
Loop 3
Loop 1
Loop 2
Typical Applications:
NC
NO
COM
-
+
Positive or Negative Power
Output (Choose NO or NC)
Positive or negative output:
}
Power for SK-910RAQ
/ SK-910RA-4Q
NC
NO
COM
-
+
12VDC receiver power driving a 12VDC appliance
}
Power for SK-910RAQ /
SK-910RA-4Q
Positive or Negative
Power Source
12VDC O/P
GND
+
12VDC
NC
NO
COM
-
+
24VAC(1) Output
12VDC receiver power input,
24VAC output driving a motor
For SK-910RAVQ /SK-910RAV-4Q and
SK-910RAV2Q / SK-910RAV2-4Q
24VAC(1) Input
GND
+
12VDC
24VAC(2)
CUT LP3 TO USE EXTERNAL ANTENNA
(+)
(+)
(+)
(+)
(+)
(((((-
-
-
-
-)))))
Electromagnetic lock
Loop 4
Ext. range antenna connector
-
+
GND
DEVICE
#1
DEVICE
#2
+
3~13.8VDC
* For SK-910RAVQ / SK-910RAV-4Q
** For SK-910RAV2Q / SK-910RAV2-4Q
CH 1 Output*
CH 2 Output**
Page 2
Page 3
Motor