SECO-LARM ENFORCER MVE-PB020Q Manual Download Page 2

ENFORCER Composite Video Balun

 

2

 

                                                        

SECO-LARM U.S.A., Inc.

 

 

 

 

Overview:  

Installation: 

1.

 

Make sure the maximum distance between the video 
source and display does not exceed the maximum range of 
the video baluns.

 

2.

 

Run the UTP cable from the video source to where it will 
be connected to the display destination.

 

3.

 

Connect UTP cable to the two video baluns. 

 

For standard baluns slide the cover off of the video balun 
and connect two wires to the terminal block located inside 
the balun. See figure 1. 

4.

 

For the correct length of bare wire, see figure 3 on page 3. 
For snap-in baluns connect the RJ 45 plug according to 
T568B wiring standards. Plug the video baluns into the RCA 
connectors on the source and destination. 

 

 

NOTE: The baluns are polarity-sensitive. Observe 
correct polarity.
 
 
 
 

Wire Exit Holes 

NOTE: Composite baluns are connected in pairs. One connects to the video source RCA 

output connector, and the other connects to the video destination RCA input connector. 

Center-pin 

(positive) 

Shielding 

(ground) 

Figure 1 – Video balun with 

cover removed 

   

Shielding 

(ground) 

Pin 7 (-) 

Pin 8 (+) 

Modular Balun: 

Snap-in Balun: 

Please use T568B wiring standard for RJ45 connectors. 

 

 

Figure 2 – Connecting 

Cat5e/6 Cable 

ENFORCER Composite Video Balun  

 

 

SECO-LARM U.S.A., Inc                                                                                        3 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sample Application #1: Standard Composite Video Baluns  

Composite Video 

Source, VCR, 

Gaming System  

Display 

Up to 2,230’ (680m) 

 

5.

 

Test the connection by powering up the video 
source and destination. 

 

6.

 

If using standard baluns, replace the covers on the 
video baluns and make sure the wires exit through 
the two small holes on the back of the units.

 

 

 

NOTE: Bare wires must not be exposed 

outside the video baluns.

 

Sample Application #2: Modular Snap-in Composite Video Baluns  

MVE-PB010Q

 

MVE-PB010Q

 

(wall plates not included) 

Up to 2,230’ (680m) 

 

MVE-PB020Q

 

MVE-PB020Q

 

Figure 3 – Video balun with 

cover removed 

Cat5e/6  

ENFORCER 

Composite Video Balun 

SECO-LARM 

Ideal Copper Length 

Expose ¼” copper wire of the UTP for 

connection to the balun.  Use the “ideal 

copper length” guide on the balun. 

SECO-LARM has a complete line of audio/video products. 

Please visit www.seco-larm.com for more information. 

Display 

ENFORCER 

ENFORCER 

Composite Video 

Source, VCR, 

Gaming System  

Component Video 

Source 

Display 

MVE-PB010Q

 

MVE-PB010Q

 

Sample Application #3: Component Video  

ENFORCER 

ENFORCER 

ENFORCER 

ENFORCER 

ENFORCER 

ENFORCER 

Pb 

Pb 

Pr 

Pr 

Up to 2,230’ (680m) 

Reviews: