15
DIP 1 = T. PAUSE:
(Aut. closing time prog. max. 4 minutes)
The control unit is supplied by the manufacturer with the automatic closing feature DIP 1
= ON and timer (default 15 sec.).
Proceed as follows to change the automatic closing time with the control unit stopped:
set DIP 1 and DIP 2 = ON, briefly press the operating button or the Radio Control key pro-
grammed earlier. The control unit will emit three acoustic signals to launch the program-
ming. Wait for the desired time, then send a command again for a moment. The control
unit will emit four acoustic signals at the end of programming meaning the automatic
closing time is being saved. Then go back to DIP 2 = OFF to end the operation.
If instead you do not want the automatic closing feature, set DIP 1 = OFF.
DIP 2 = MOT T. PROG.:
(Motor Time Prog. max. 4 minutes)
The control unit is supplied by the manufacturer with a working time motor predefined
equal to 30 sec.
Proceed as follows to change the work Time of the Motor, only with the control unit clo-
sed: set DIP 2 = ON, briefly press the operating button or the Radio Control key program-
med earlier. The control unit will emit three acoustic signals to launch the programming,
the control unit will open the door and when it reaches the desired position briefly press
again. The control unit will stop the door and emit four acoustic signals that indicate the
end of programming. Then go back to DIP 2 = OFF to end the operation.
DIP 3 = Operator Present Feature AP/CH (DIP 1 = OFF):
The control unit is supplied by the manufacturer with the Operator Present Function di-
sabled.
To enable the Operator Present feature in both the Opening and Closing phases, with
the control unit stopped, set DIP 3 = ON to move the fixture. Hold down the radio control
button or the operating button for the duration of the movement.
To enable the Operator Present function for the closing phase only, repeat the operation
described above and set both DIP 3 and DIP 1 = ON.
DIP 4 = FLASHING / COURTESY LIGHT
The control unit has a 230 Vac output, for connection to a flashing light or a courtesy light.
The control unit is supplied by the manufacturer with the Flashing function enabled DIP
4 = OFF.
To enable the Courtesy light feature, with the control unit stopped, set DIP 4 = ON.
Flashing Light feature:
The 230 Vac output will be activated each time the automation
is moving, for the duration of the motor time. If the Pause Time is saved, the flashing light
will be on during the Pause as well.
Courtesy Light Function:
The 230 Vac output will be activated for 3 minutes, each time
that an ascent command is given.
DIP 5 = STEP-BY-STEP / INVERTING:
The control unit is supplied by the manufacturer with the Step-by-step mode DIP 5 = OFF.
To enable the Inverting feature, with the control unit stopped, set DIP 5 = ON. This way,
you will obtain the following operation: the first impulse controls opening until the motor
time expires, the second impulse controls fixture closing. If an impulse is sent before the
motor time expires, the control unit
changes the direction
of motion in the opening
and closing phases.
Set DIP 5 = OFF to restore the previous configuration.
SOUND SIGNALS
1 x Short BEEP
= First remote control code saved.
2 x Short BEEPS
= Second remote control code saved
3 x Short BEEPS
= Start of Mot.T. Progr. / Pause T. / RDC
4 x Short BEEPS
= End of Mot.T. Progr. / Pause T. / RDC
-------------------------------------------------------------------------------------
1 x Long BEEP
= Radio control cannot be saved
2 x Long BEEPS
= Reset of radio controls
3 x Long BEEPS
= Reset of motor and pause time
PROGRAMMING OF RADIO CONTROLS:
Programming the radio control with 1 or 2 Keys.
Radio control transmission codes are programmed as follows: press the PROG button,
the control unit will emit three short beeps to launch the programming. The CODE LED
will start flashing and at the same time it will send the first code (“Up” associated with
the opening direction) of the radio control. At the same time, the control unit will emit a
short acoustic signal indicating that programming has been completed. Then the CODE
LED will start flashing quickly: send the second code (“Down” associated with the closing
direction) to be saved. The CODE LED will remain on and at the same time the control unit
will emit two short acoustic signals indicating that programming has been completed.
If the second code is not sent within 10 seconds, the control unit will exit the program-
ming phase by emitting four short acoustic signals. Select the function with only 1 key
of the radio control.
Remote transmission code programming
(only works with Y17/19 series Radio Controls).
This procedure allows to program the transmission code remotely, without using the PROG
button on the unit itself, but remotely following the operation.
The long distance transmission code is programmed as follows: press the first and second keys
Summary of Contents for LRX 2329
Page 1: ...LRX 2329 NEW ...
Page 2: ......
