the SET key once the desired threshold has been reached – at
this moment, the selected value will be stored and the WIND
LED will remain lit (
for example: 5 WIND LED double-flashes =
25 km/h).
The operation may be repeated if a mistake is made during
programming.
4)
SUN SENSOR
( Sun Sensor ON/OFF )
Enabling the Sun Sensor
The control unit comes with the Sun Sensor disabled (SUN
SENSOR LED OFF).
The Sun Sensor may be enabled in the following way: press
the SEL key until the SUN SENSOR LED flashes, then press
the SET key briefly; at this moment the SUN SENSOR LED
remains lit and the Sun Sensor will be enabled. Repeat the
operation to disable the Sun Sensor.
Enabling the Sun Sensor using a 3-button radio control
(BeFree x3 - X6):
The Sun Sensor may be enabled in the following way: hold
down the (+) key on the radio control that was programmed
previously for 5 seconds; at the same time the control unit will
cause the shutter to move Up/Down for 1 second to confirm
that the Sun Sensor has been enabled, and the SUN SENSOR
LED will remain lit. Repeat the operation to disable the Sun
Sensor by following the same procedure, but instead holding
down the (-) key for 5 seconds.
5)
RAIN SENSOR
( Rain Sensor ON/OFF )
Disabling the Rain Sensor
The control unit comes with the Rain Sensor enabled (RAIN
SENSOR LED ON).
The Rain Sensor may be disabled in the following way: press
the SEL key until the RAIN SENSOR LED flashes, then press
the SET key briefly; at this moment the RAIN SENSOR LED
switches off and the Rain Sensor will be disabled. You can
repeat the operation to enable the Rain Sensor.
EXTENDED MENU
The control unit is supplied by the manufacturer with the option
of selecting only the functions listed in the main menu.
To enable the functions of the extended menu proceed as
follows: press the SET key and hold for 5 seconds; the SUN,
RAIN and R. HEAT LEDs will flash and the user has 30
seconds within which to select the functions of the extended
menu using the SEL and SET keys. After another 30 seconds
the control unit returns to the main menu.
---------------------- EXTENDED MENU -----------------
Reference LED LED Off LED On
A) CODE remote PGM = OFF remote PGM = ON
B) T. MOT. Aut. movement lock = OFF Aut. movement lock =
ON
C) WIND SPEED Safety upward = OFF Safety upward =
ON
D) SUN SENSOR RAIN inversion = OFF RAIN inversion =
ON
E) RAIN SENSOR Aut. movements 5 min. Aut. Movements 10
min.
C) SUN Flashing beacon ON/OFF
C) RAIN Flashing beacon ON/OFF
G) R. HEAT Flashing beacon ON/OFF
A) CODE
(Remote programming of radio control):
The control unit allows the transmission code to be
programmed by remote, without using the SEL key.
To programme the transmission code remotely, proceed as
follows: send the radio control code continuously for more than
10 seconds and the control unit will enter the programming
mode as described above for the CODE LED in the main
menu.
The control unit is supplied by the manufacturer with remote
programming of the transmission code not enabled; to enable
the function proceed as follows: check that the extended menu
is enabled (SUN, RAIN and R. HEAT LEDs flash), using the
“SEL” key navigate to CODE LED when flashing and press the
“SET” key: the CODE LED lights up permanently and
programming is completed. Repeat the operation to restore the
previous configuration.
B) T. MOT. (Automatic movement lock):
The control unit enables the prevention of Automatic
movements (Up / Down sun blind movements on the Sun
Sensor command or Automatic Sensors function), so that if a
Stop command is sent from a radio control during the
movement, the control unit momentarily locks the Automatic
movements until a new Up or Down command is sent. The
control unit is supplied by the manufacturer with the Automatic
Movement Lock disabled; to enable the function proceed as
follows: check that the extended menu is enabled (SUN, RAIN
and R. HEAT LEDs flash), using the “SEL” key navigate to T.
MOT. LED when flashing and press the “SET” key: the T.
MOT. LED lights up permanently and programming is
completed. Repeat the operation to restore the previous
configuration.
C) WIND ( Safety Upward Movement ) :
The control unit is supplied by the manufacturer with the Safety
upward movement function disabled; if you wish to enable the
function, in such a way that after 12 hours of inactivity of the
Wind Sensor the control unit automatically control the safety
upward movement, proceed as follows: check that the
extended menu is enabled (SUN, RAIN and R. HEAT LEDs
flash), using the “SEL” key navigate to WIND LED when
flashing and press the “SET” key: the WIND LED lights up
permanently and programming is completed. Repeat the
operation to restore the previous configuration.
D) SUN SENSOR ( Rain control movement inversion ) :
The control unit is supplied by the manufacturer with the Rain
Control = Upward Movement Control association, that is to say
when the rain sensor detects the rain, the control unit controls
the upward movement. If you wish that the control unit controls
the downward movement when rain is detected by the rain
sensor, proceed as follows: check that the extended menu is
enabled (SUN, RAIN and R. HEAT LEDs flash), using the
“SEL” key navigate to SUN SENSOR LED when flashing and
press the “SET” key: the SUN SENSOR LED lights up
permanently and programming is completed. Repeat the
operation to restore the previous configuration.
E) RAIN SENSOR (Automatic sensor action Time) :
The control unit is supplied by the manufacturer with the
Automatic sensor action Time of 4 minutes; if you wish to set
10 minutes to reduce the motor movements, proceed as
follows: check that the extended menu is enabled (SUN, RAIN
and R. HEAT LEDs flash), using the “SEL” key navigate to
RAIN SENSOR LED when flashing and press the “SET” key:
the RAIN SENSOR LED lights up permanently and
programming is completed. Repeat the operation to restore the
previous configuration.
R
ESET
To reset the default configuration of the control unit, press the
SEL and SET buttons simultaneously; all indicator
LEDs will
switch on and then off again immediately.
3
Rev. 1.2 31/01/08
