manualshive.com logo in svg

Sears CRAFTSMAN 944.605200, Owner'S Manual, Page: 39 / 52

Share
Download
Sears CRAFTSMAN 944.605200 Owner'S Manual Download Page 39

39

REPAIR PARTS

TRACTOR - - MODEL NUMBER 944.605200

ENGINE

1         170546X505     Control Throt Paddle
2         17720408          Screw Hex Thd Cut 1/4-20 x 1/2
3          - - - - - - - -        Engine (See Breakdown) 

                                   B&S Model 407577-0283-E1

4         149723              Muffl er Exhaust
5         159955              Exhaust Asm. Left
6         160589              Exhaust Asm. Right
8         171877              Bolt 5/16-18 unc x 3/4
10       162797              Heat Shield Lt
13       165391              Gasket Muffl er
14       148456              Tube Drain Oil Easy
17       17060624          Screw Thdrol 3/8-16 x 1-1/2 Tytt
23       169837              Shield BRN/DBR Guard
25       187766X505     Control Choke
29       137180              Arrestor Spark
31       157103              Tank Fuel 3.5 STL W/O Sensor 
32       161696              Cap Fuel Gauge 
33       123487X           Clamp Hose Blk 
34       106082X           Strip Foam
37       8543R               Line Fuel 
38       181654              Plug Drain Oil Easy
39       109227X           Pad Spacer
45       17000612          Screw Hex Wsh Thdrol 3/8-16 x 3/4
72       183906              Screw Socket Head 5/16-18 x 1
81       73510400          Nut Keps Hex 1/4-20 unc

KEY    PART              
NO.     NO.                   DESCRIPTION

NOTE:

 

 

All component dimensions given in U.S. inches

1 inch = 25.4 mm

Summary of Contents for CRAFTSMAN 944.605200





















































Reviews:

No comments