background image

CONTENTS

Safety ...................................................................................2

Pump Performance/General Information ...........................3

Before You Start/Tools/Materials ........................................4

Installation 

Piping ....................................................................4-5, 8-12

Electrical ........................................................................6-8

Helpful Hints.................................................................11-12

Parts ..............................................................................13-15

INTRODUCTION

Please take a few minutes to read our instructions before in-
stalling your submersible pump. It will help to assure per-
fect installation and help you avoid needless service
expenses.

Carefully read and follow all safety instructions in this man-
ual or on pump. 

This is the safety alert symbol. When you see this sym-

bol on your pump or in this manual, look for one of

the following signal words and be alert to the potential for
personal injury! 

warns about hazards that 

will

cause serious

personal injury, death or major property damage if ignored.

warns about hazards that 

can

cause serious

personal injury, death or major property damage if ignored.

warns about hazards that 

will

or 

can

cause

minor personal in jury or property damage if ignored. 

The word 

NOTICE

indicates special instructions which are

important but not related to hazards. 

To avoid risk of serious bodily injury and property
damage, read safety instructions carefully before in-
stalling pump. 

1.

Under certain conditions, submersible

pumps can develop extremely high pres-
sure. Install a pressure relief valve capable

of passing entire pump flow at 75 PSI (517kPa).

Do not allow pump, pressure tank, piping, or

any other system component containing water

to freeze. Freezing may damage system, leading to in-
jury or flooding. Allowing pump or system compo-

nents to freeze will void warranty.

2. Follow local and/or national plumbing and electrical

codes when installing pump. 

3. Keep well covered while installing pump to prevent

leaves and other foreign material from falling into well,
contaminating the well and possibly damaging the pump. 

4. Protect pump and piping system from freezing. Allowing

pump or water system to freeze could severely damage
pump and voids warranty. 

5. To protect system against over-pressure, install a pressure

relief valve (Stock No. 27229).

6. With a new well, test well water for purity before using.

Consult your local Health Department for procedure. 

Hazardous voltage. Can shock, burn,

cause death, or start fires.

7. Disconnect electrical power source before installing or

working on pump. 

8. Use pump only in a well application. 
9. Correct fusing, wiring and grounding are essential to

proper operation. See Page 6 for electrical instructions. 

10. Line voltage and frequency listed on motor nameplate

must agree with line voltage and frequency of electrical
power supply. 

11. Use of fuses or wire smaller than size recommended in

owner's manual can cause overheating, possible  fires,
and will void warranty. 

2

FULL ONE YEAR WARRANTY ON CRAFTSMAN

®

HYDROGLASS

®

SUBMERSIBLE WELL PUMPS

For one year from the date of purchase, Sears will repair or replace this pump, free of charge, if defective in material or 
workmanship.

LIMITED WARRANTY ON CRAFTSMAN

®

HYDROGLASS

®

SUBMERSIBLE WELL PUMPS (not including Controls)

After one year and through three years from the date of purchase, Sears will furnish, free of charge, a replacement part for any
defective part. You pay for labor.

This warranty does not cover repairs or replacement parts necessary because of abuse or negligence including failure to install,
adjust and operate this pump according to the instructions in the owner’s manual.

LIMITATION OF  LIABILITY

SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE TO PROPERTY OR ANY INCIDENTAL OR CONSEQUENTIAL LOSS OR 
EXPENSE FROM PROPERTY DAMAGE DUE DIRECTLY OR INDIRECTLY FROM THE USE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE
UNITED STATES.

This warranty applies only while the product is in use in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from  state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

RULES FOR SAFE INSTALLATION AND OPERATION

Summary of Contents for Craftsman 390.284021

















Reviews: