instructions for
hydraulic press 5.4tonne economy bench type
model no:
yK6ecb.V2
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFety
1.1.
General saFety
9
familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
9
maintain the
press in good condition (use an authorised service agent).
9
replace or repair damaged parts.
Use recommended parts only. Non authorised parts may be dangerous and will invalidate the
warranty.
9
Keep the press clean for best and safest performance.
9
locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is
9
adequate lighting.
9
securely attach the press to a flat, firm, level surface capable of supporting the weight of press and any workpiece taking into account
clearance for workpieces.
9
ensure the workpiece is correctly secured before operating the press.
WarninG!
Always wear approved eye or face protection when operating the press.
9
remove ill fitting clothing. remove ties, watches, rings, loose jewellery and contain long hair.
9
Keep hands and body clear of the work table when operating the press.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip steel toe-capped shoes/boots.
9
Keep children and unauthorised persons away from the working area.
8
do not
operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
do not
use to compress springs or any other item that could disengage and cause a potential hazard.
8
do not
stand directly in front of the loaded press and never leave a loaded press unattended.
8
do not
use the press for any purpose other than that for which it is designed.
8
do not
make any modifications to the press.
8
do not
adjust or tamper with the safety valve.
8
do not
exceed the rated capacity of the press.
8
do not
apply off-centre loads.
8
do not
allow the workpiece or the press plates to fall from the work table.
8
do not
get the press wet or use in damp or wet locations or areas where there is condensation.
8
do not
operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9
When not in use, release pressure from the hydraulic unit and clean the press. stand or store the press plates in a safe location.
WarninG!
Always position the press against a wall. if the press is situated in the open workshop, it is essential that a guard be
placed at the rear of the unit. this will prevent injury to bystanders in the event of the workpiece ejecting suddenly.
WarninG!
the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur.
it must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2. introduction
e
conomy range suitable for the serious enthusiast or occasional professional use. Made from high quality steel with a powder coated paint finish
to help corrosion resistance.
3. speciFication
model no: ............................................................YK6ecB.V2
type: ........................................................................hydraulic
capacity: .................................................................. 5.4tonne
ram stroke: ................................................................ 125mm
ram diameter: ............................................................. 36mm
max. height ram to table: ......................................... 145.5mm
min. height ram to table: ............................................ 20.5mm
table aperture: ............................................................. 56mm
Working table depth: .................................................. 136mm
YK6ecB.V2 | issue:2 (3) 20/08/18
Original Language Version
© Jack sealey limited
Working table width: ................................................... 340mm
overall height: ............................................................ 800mm
Weight: ........................................................................ 26.4kg
refer to
instruction
manual
Wear protective
gloves
Wear face
mask
Wear protective
clothing
Wear safety
footwear
Warning:
crushing of
hands
