SUBMERSIBLE POND PUMP 1100LTR/HR 230V
MODEL NO:
WPP1100
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend
that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into
a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device
by contacting your Sealey stockist.
IMPORTANT: You must
also read and understand the following instructions concerning electrical safety:
1.1.1. The
Electricity at Work Act 1989
requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure
that none is loose.
1.1.6.
IMPORTANT:
Ensure that the voltage marked on the appliance matches the power supply to be used
and that the plug is fitted with the correct fuse - see fuse rating at right.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired
or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged, cut the cable just
above the plug and
dispose of the plug safely
.
1.2.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all
wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the
restraint is tight.
1.2.1.
Double insulated products, which are always marked with this symbol
, are fitted with live (brown) and neutral (blue) wires only.
1.2.2.
To rewire, connect the wires as indicated above -
DO NOT
connect
either wire to the earth terminal.
IMPORTANT:
Products which require more than 13amps are supplied
without a plug. In this case you must contact a qualified electrician to
ensure that a suitably rated supply is available. We recommend that
you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.2.3.
If an extension reel is used it should be fully unwound before
connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important
and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which
may be used in the other output sockets, we recommend the use
of 2.5mm² section cable. If an extension reel is to be used outdoors,
ensure it is marked for outdoor use.
WPP1100 | Issue 6 (H,F,2,3) 28/02/2019
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Replacement fuse
rating: 13AMP
Warning!
Electricity
