1. safety instructions
instructions for:
eGr Valve actuator/tester
model
no
:
Vs926
thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT
:
PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents,
WarninGs anD cautions. use tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH it is
intenDeD. faiLure to Do so May cause DaMaGe anD/or PersonaL inJury anD WiLL inVaLiDate tHe
Warranty.
1.2 GeneraL safety
r
WarninG!
Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
×
Do not
use tools if damaged.
ü
maintain tools in good and clean condition for best and safest performance.
ü
ensure that a vehicle which has been jacked up is adequately supported with axle stands.
ü
ensure that all tools are removed from the engine bay upon completion of the job.
ü
Wear approved eye protection. A full range of personal safety equipment is available from your sealey dealer.
ü
Wear suitable clothing to avoid snagging.
Do not
wear jewellery and tie back long hair.
ü
Keep children and unauthorised persons away from the work area.
×
Do not
attempt to start engine or move vehicle whilst in gear.
Original Language Version
Vs926 issue: 1 - 21/11/12
© Jack sealey ltd
1.1.
eLectricaL safety.
WarninG!
it is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products before use to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
device (rcd) is used. it is particularly important to use an rcd with portable products that are plugged into a supply which is not protected
by an rccB. if in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
you must
also read and understand the following instructions concerning electrical safety.
1.1.1. the
electricity at Work act 1989
requires that all portable electrical appliances, if used on business premises, are tested by
a qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the
Health & safety at Work act 1974
makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators.
if in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
see 1.1.1. and 1.1.2. and use a Portable Appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose.
1.1.6.
important:
ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in diagram at the right.
1.1.7.
Do not
pull or carry the appliance by the power cable.
1.1.8.
Do not
pull the plug from the socket by the cable.
1.1.9.
Do not
use worn or damaged cables, plugs or connectors. immediately have any faulty item
repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is damaged,
cut the cable just above the plug and
dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) connect the Green/yeLLoW earth wire to the earth terminal ‘e’.
b) connect the BroWn live wire to the live terminal ‘L’.
c) connect the BLue neutral wire to the neutral terminal ‘n’.
d) after wiring: check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
double insulated products, which are always marked with this symbol, are fitted with live (brown)
and neutral (blue) wires only. to rewire, connect the wires as indicated above -
Do not
connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. in this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. if an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
IMPORTANT:
These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions, or a proprietary
manual, to establish the current procedure and data.
WARNING: The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may
occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
recommended fuse rating: 3amp
Summary of Contents for VS926
Page 3: ......
