background image

instructions for

ir & rF key Fob tester

model no: 

Vs921

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  sAFety

‰

‰

‰‰

WArNiNG!

 

Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this

    equipment.

 

9

  

familiarise yourself with the applications, limitations, and potential hazards of the tester.

 

9

   Keep the tester clean and in good condition.

 

9

   Protect the tester from the following: static electricity, High temperatures.

 

8

  

Do Not

 get the tester wet or use in damp or wet locations or areas where there is condensation.

 

8

 

  Do Not

 use the tester for any purpose other than for which it is designed.

 

8

   Do Not

 allow untrained persons (particularly children) to operate the tester.

 

8

  

Do Not

 operate the tester

 

when you are tired or under the influence of alcohol, drugs or intoxicating medication.

2. 

i

 

iNtroDuctioN

detects and confirms radio frequency and/or infra red emission from key fobs and remote controls. Helps diagnose faults quickly and easily without 

the need to dismantle the fob, remote or vehicle. magnetic backing sticks to the side of any ferrous surface making distance test of transmitter a 

possibility. suitable for a wide variety of vehicle and electronic/electrical applications. Powered by a 9V battery (not included).

3.  speciFicAtioN

model no: .................................................................... Vs921

detects: .................................... infra-red or radio frequency

rf: ...................................... 418mHz, 433-434mHz, 868mHz

4.  operAtioN

4.1. 

  

AsseMbLy

4.1.1. 

  

slide the battery cover off from the rear of the tester

.

4.1.2.   

insert a 9V/PP3 battery (not included).

4.1.3.   

make sure polarity is correct.

4.1.4.   

replace battery cover.

4.2. 

  

operAtioN

4.2.1. 

  

switch the unit on by pressing the “on/off” button, this will illuminate 

 

the green led at the top of the tester.

4.2.2.   

secure the tester to a metal surface using the magnetic pad on the rear 

 

of the tester.

4.2.3.   

make sure the tester is at least 3 metres away from other electrical

 

devices which may emit an electrical frequency. interference with the unit

 

will cause the led to illuminate/flash. 

4.2.4.   

Aim a working key fob at the tester and operate the key fob, a led at 

 

the top will flash once. now test the suspect key fob.

4.2.5.   

if the suspect key fob does not trigger the led, change the key fob’s 

 

battery and repeat the procedure.

4.2.6.   

the tester can also be used to determine the strength/range of a key 

 

fob’s signal.

Note:

  the tester need not be switched off as it has an “auto-shutdown” function 

 

  (approximately 1 minute without use).

4.2.7. 

 

 

this tester can also pick up test home entertainment remotes and 

 

other similar devices.

refer to

instructions

Vs921| issue 3(i) 20/01/17

Original Language Version

© Jack sealey limited

Reviews: