background image

AUTOMATIC BRAKE AND CLUTCH BLEEDER

MODEL NO: 

VS0205

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

9

Keep this product in good working order and condition, take immediate action to repair or replace damaged parts.

 

9

Use approved parts only. Unapproved parts may be dangerous and will invalidate the warranty. 

 

9

Keep children and unauthorised persons away from the work area.

 

9

Keep work area clean and tidy and free from unrelated materials.

 

9

Ensure the work area has adequate lighting.

 

8

DO NOT

 use the kit to perform a task for which it is not designed.

 

8

DO NOT

 allow untrained persons to use the kit.

 

8

DO NOT

 use when tired or under the influence of drugs, alcohol or intoxicating medication.

 

9

After use, clean equipment and store in a cool, dry, childproof area. 

 

9

Dispose of waste liquids in accordance with local authority regulations.

 

9

A

lways read and comply with the warnings on the brake fluid container.

 

9

W

ear eye protection and keep skin contact to a minimum. If brake fluid enters eyes rinse with plenty of water and seek medical advice. 

 

9

If swallowed seek medical advice immediately.

 

‰

WARNING!

 Only use new Brake Fluid, used Brake Fluid or other fluids will contaminate the system and possible brake system failure 

may result. 

WARNING!

 

DO NOT

 pollute the environment by allowing uncontrolled discharge of fluids.

 

‰

WARNING!

 

Brake fluid is flammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.

 

‰

WARNING!

 

Brake fluid will damage paintwork. Any spillage should be flushed with water immediately.

2.  INTRODUCTION

F

ast, easy and effective bleeding of brakes and clutch using air from tyre. Innovative design incorporates valve for control of air pressure, extra-long 

air hose for use with larger vehicles and magnetic reservoir base to prevent accidental spillage. Suitable for use with ABS systems. Supplied with 

range of common adaptors.

3.  SPECIFICATION

Model no: ......................................................................VS0205

M

aximum Air Supply:

 .....................................................  20 psi

Accessories

 

1 x 25mm Cap and Seal for Lockheed Systems.

 

1 x 27mm Cap and Seal for VAG.

 

1 x 44/45mm Cap with 2 Seals (1 x thin for 44mm Cap and 1 x thick for 45mm Cap)

 

for metal Girling and ATE Systems

 

1 x 46mm Cap and Seal for some Girling Systems 

 

2 x Bleed Pipes

4.  OPERATION

4.1.    

BRAKE BLEEDING PROCEDURE

 

Refer to the vehicle manufacturer’s instructions for brake bleeding and wheel 

 

sequence before proceeding. If no specific instructions from the vehicle manufacturer 

 

exist, follow the instructions detailed below.

 

‰

  

WARNING!

 Familiarise yourself with hazards of brake fluid - read manufacturer’s 

 

instructions on the container.

 NOTE: 

Ensure that the brakes are adjusted before proceeding with bleeding the brakes.

4.1.1. 

  

For vehicles fitted with servo assisted brakes, pump the brake pedal two or three  times with the engine switched off to evacuate the air  

 

from the servo.

4.1.2. 

  

Remove the reservoir cap from the vehicles brake master cylinder, select and fit, see fig.1, the appropriate adaptor cap to the automatic  

 

brake bleeder and connect to the master cylinder. 

4.1.3.   

Adjust the tyre pressure of one of the vehicles tyres or use a spare wheel to a maximum of 20 psi and connect the automatic brake    

 bleeder.

4.1.4.   

Pressure test the bottle with no brake fluid to ensure that the bottle has no leaks and then release the pressure, disconnect from the tyre  

 

and fill the pressure bottle with new clean brake fluid.

V

S0205        Issue 4 (3, 4) 10/08/18

Original Language Version

© Jack Sealey Limited

Refer to 

instruction

manual

Wear Protective 

Gloves

Wear Eye 

Protection

Reviews: