Keep this product in good working order and condition, take immediate action to repair or replace damaged parts.
Use approved parts only. Unapproved parts may be dangerous and will invalidate the warranty.
Keep children and unauthorised persons away from the work area.
Keep work area clean and tidy and free from unrelated materials.
Ensure the work area has adequate lighting.
DO NOT
use the kit to perform a task for which it is not designed.
DO NOT
allow untrained persons to use the kit.
DO NOT
use when tired or under the influence of drugs, alcohol or intoxicating medication.
After use, clean equipment and store in a cool, dry, childproof area.
Dispose of waste liquids in accordance with local authority regulations.
Always read and comply with the warnings on the brake fluid container.
Wear eye protection and keep skin contact to a minimum. If brake fluid enters eyes rinse with plenty of water and seek medical advice. If
swallowed seek medical advice immediately.
WARNING!
Only use new Brake Fluid, used Brake Fluid or other fluids will contaminate the system and possible brake system failure may
result.
WARNING! DO NOT
pollute the environment by allowing uncontrolled discharge of fluids.
WARNING!
Brake fluid is flammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.
WARNING!
Brake fluid will damage paintwork. Any spillage should be flushed with water immediately.
WARNING!
Do not allow the fluid capacity in the unit to fall below ½ litre during the bleeding process otherwise air may enter the
system.
I
NSTRUCTIONS FOR:
BRAKE & CLUTCH PNEUMATIC
PRESSURE BLEEDER
MODEL No:
VS0204A
One-man pressure brake and clutch bleeding system suitable for the professional workshop. Low pressure tank (20-40psi) can be
pre-charged with compressed air - making the unit fully portable. Large reservoir means reduced risk of running the system dry during bleed-
ing process or complete fluid change. Suitable for use on ABS systems. Features a long delivery hose for operation with a low level ramp and
long reach handle for easy mobility. Supplied with Ø42mm cap with 90° angled connector which is suitable for most European models. For
other applications order optional Brake reservoir Cap 42mm Straight Connector - Model no. VS0204SA, Universal Adaptor - Model no.
VS820UA or Brake & clutch Bleeder Cap Set - Model no. VS0204B.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VS0204A
Air Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-40psi
Air consumption:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5cfm
Inlet size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Tank capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.0 litres
Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7mtr
Fig.1
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
Refer to
instructions
Wear eye
protection
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
VS0204A Issue: 1 - 05/05/16
Original Language Version
© Jack Sealey Limited
