DOUBLE DIAPHRAGM FUEL TRANSFER
PUMP
Model no:
TP6918
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETy
WARNING!
ensure all Health and Safety, local authority and general workshop practice regulations are strictly adhered to when using
this equipment.
▲
DANGER!
Petrol is a highly flammable liquid and any spillage will evaporate to form a flammable, heavier than air vapour, which is
easily ignited. Common sources of ignition include, but are not limited to, smoking and lighting matches, welding and cutting
equipment, heaters, all types of electrical equipment unless specifically designed as suitable for use in a flammable atmosphere. even
low voltage inspection lamps, if damaged can ignite petrol vapour.
Please take time to read the following safety information before commencing work with the TP6918.
9
Familiarise yourself with the applications, limitations and potential hazards of this product.
9
Maintain the pump in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts will invalidate the warranty.
9
Use only with oils, petrol, diesel, paraffin, anti-freeze, degreasants and other non-corrosive fluids.
9
ensure safety eye protection and protective clothing are worn when using this product.
9
Keep a foam or dry powder fire extinguisher nearby.
9
ensure that containers cannot easily be knocked over during filling.
9
Keep the work area clean and uncluttered and ensure that there is adequate lighting.
9
Remove all combustible materials from the work area.
9
Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
HSe guidance recommends use of metal containers with secure caps for holding drained fuel.
9
Mark fuel containers with hazard labels to identify the contents.
9
Keep any fuel containers in a well ventilated, lockable store, preferably away from the working area.
9
Soak up any spill immediately using absorbent granules or similar material.
9
dispose of waste liquids in accordance with local authority regulations.
8
DO NOT
use an open flame or smoke anywhere near the tool or around stored fuel.
8
DO NOT
use the pump to transfer hazardous or harmful chemicals, corrosive liquids, solvents, alkalis or acids.
8
DO NOT
use the pump with water.
8
DO NOT
use the pump near sources of heat or sparks.
8
DO NOT
allow work which can produce a source of ignition, such as welding, electrical or other hot work, to be carried out whilst
dispensing fuel.
8
DO NOT
use cordless, mobile phones or pagers, ensure these items are turned off before dispensing fuel.
8
DO NOT
use the pump for any purpose other than for which it is designed.
8
DO NOT
attempt to move the fluid drum by pulling on the pump.
8
DO NOT
use whilst under the influence of drugs, alcohol or other intoxicating medication, or if you are fatigued, Keep the pump clean
and well oiled and store in a safe, dry, childproof location when not in use.
Users/Businesses should perform their own hazard risk assessment based on their specific environment and following the
guidelines laid out above.
2. INTRODUcTION
Self-priming high performance double diaphragm lever pump. Heavy-duty die cast aluminium pump head with stainless steel pistons and fuel
resistant nitrile rubber diaphragm. 2”BSP Connector and telescopic dip tube to suit 50 to 205ltr drums. Approximately 800ml per full stroke
discharge. Supplied with 8ft anti-static discharge hose and delivery nozzle with holder. Suitable for various oils, petrol, diesel, antifreeze,
paraffin and other non-corrosive fluids.
3. ASSEMBLy
3.1.
Slide the bung nut onto the octagonal base at the pump inlet. Tighten the bung on the base using the two bolts on the bung.
3.2.
Prepare the threads of the telescopic suction tube with some PTFe tape and screw into the pump inlet and tighten.
3.3.
Fully extend the telescopic tube and insert the suction tube through the 2” threaded hole into the drum, until the suction tube hits the
bottom of the drum. Screw the bung nut into the drum.
3.4.
Connect the dispensing nozzle onto one end of the rubber hose and the other into the outlet of the pump. Use PTFe tape on both
threads before assembly.
TP6918 Issue 2 25/01/19
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear protective
clothing
