![background image](http://html.mh-extra.com/html/sealey/tc10/tc10_instructions-manual_1227357003.webp)
3. introDuction
Automatic tyre changer capable of changing 11” to 24” wheel rims. suitable for most cars and light commercial vehicles. Air operated rear
tilting column and head lock. Protects alloy wheels with the added feature of plastic protectors, fitted to the clamping jaws and mounting head.
Supplied with 485mm tyre lever, integrated tyre inflator, tyre soap tub, air regulator and lubricator. Model No.TC10A Assist Arm is required for
use with low profile and run flat tyres. See Sealey website for demonstration video.
4. SPecification
model no ....................................................................... tc10
Wheel Ø min/max ...........................internal clamping 11”-20”
......................................................external clamping 12”-24”
Wheel depth min/max ........................................12” (305mm)
turntable Ø ........................................................
26” (660mm)
B
ead breaking force .................................................. 2500kg
tyre inflater ...............................................0-10bar (0-145psi)
voltage/Phase .......................................................230v - 1ph
motor ........................................................................... 1.1KW
operating Pressure ............................... 8-10bar (115-145psi)
inlet size ...................................................................
1/4”BSP
dimensions (W x d x H) .......................
690 x 1100 x1900mm
Weight ..........................................................................
246kg
optional Additional tool ..............................tc10A Assist Arm
5. PoSitioning anD aSSembly
5.1.
The minimum required space around the machine is shown in fig. 1. It should be bolted to a flat/level surface using
appropriate fixings as follows:
5.2.
inStallation
5.2.1.
locating the tyre changer:
5.2.1.1.
Make sure Tyre Changer is fitted/used on a dry, flat, level,
oil/grease free, concrete surface capable of supporting the
weight of the tyre changer.
5.2.1.2. the tyre changer is designed for indoors use only.
8
Do not
install or use the tyre changer outdoors, or in
damp or wet locations.
5.2.1.3. make sure to check the desired location for possible
obstructions such as a low ceiling, adequate working area,
access ways, exits. the tyre changer should be located in
an area free of flammable materials and liquids.
5.2.1.4. make sure the tyre changer is located near enough to a
plug socket so it can be plugged into directly without the
use of an extension cable.
5.2.2.
mounting the tyre changer to the floor
5.2.2.1. With assistance, and with the use of a lifting device, position
in the desired location. use the four, 13mm (1/2”) machine
mounting holes located at the base of the Body as a template
to mark the points where four floor anchor holes will be
drilled in the floor surface. Then, temporarily remove the
tyre changer.
5.2.2.2.
Where previously marked on the concrete floor surface,
drill four 13mm (1/2”) diameter, minimum 100mm deep,
anchor holes. NOTE: Be sure to blow out the cement dust
from the drilled hole.
5.2.2.3.
Move the Tyre Changer back to the desired location, and align the four machine mounting holes at the base of the Body with the four
previously drilled floor anchor holes. If necessary, level the Tyre Changer by inserting steel shims between the base of the machine
and the concrete floor surface.
Do not
exceed more than 5mm thickness of shims.
5.2.2.4.
Secure the Tyre Changer to the concrete floor surface, using four 13mm (1/2”) diameter concrete anchor bolts of appropriate length,
four washers, and four nuts (not provided).
fig.1
tc10 | issue 1 02/02/18
Original Language Version
© Jack sealey limited