Sealey STR600 Quick Start Manual Download Page 2

5.2.        aSSeMBlING tHe eND fraMeS:

 

refer to (fig.1).

5.2.1.    Place the uprights 

(a1 & a2)

 on the floor with the inner edges facing each other.

5.2.2.    Take one horizontal brace 

(B1)

 and one spacer 

(D)

. Insert into the upright 

(a2)

 at the base area drilled hole and loosely secure using    

  a m6 x 45mm bolt 

(f)

 and a m6 nut 

(G)

.

5.2.3.    Place the other upright 

(a1)

 so that the horizontal brace 

(B1)

 aligns with the base area drilled hole. Take one of the diagonal braces    

 

(c1)

 and insert into the upright 

(a1)

 so that the hole aligns with the hole in the horizontal brace 

(B1)

 and the drilled hole in the upright    

 

(a1)

. loosely secure using a m6 x 45mm bolt 

(f)

 and a m6 nut 

(G)

.

5.2.4.    Align the other end of the diagonal brace 

(c1)

 with the corresponding hole in the opposite upright 

(a2).

 Take another diagonal brace 

(c2)

    

  and align with the same hole on diagonal brace 

(c1)

 and on the upright 

(a2)

. loosely secure using a m6 x 45mm bolt 

(f)

 and a m6 nut 

(G)

.

5.2.5.    Align the other end of the second diagonal brace 

(c2)

 with the corresponding hole in the opposite upright 

(a1)

. Take a third diagonal brace  

 

(c3)

 and align with the second diagonal brace 

(c2)

. loosely secure both to the upright 

(a1)

 using a m6 x 45mm bolt 

(f)

 and a m6 nut 

(G)

.

5.2.6.    Align the remaining end of diagonal brace 

(c3)

 with the top hole of the opposite upright 

(a2)

. Place a horizontal brace 

(B2)

 aligned with    

  the diagonal brace 

(c3)

 and across to the opposite upright 

(a1)

. loosely secure the end of horizontal brace 

(B2)

, along with the diagonal    

 brace 

(c3)

 to the upright 

(a2)

 using a m6 x 45mm bolt 

(f)

 and a m6 nut 

(G)

. Align the other end of the horizontal brace 

(B2)

 with the    

  top hole of the upright 

(a1)

. Place a spacer in the gap and loosely secure with a m6 x 45mm bolt 

(f)

 and a m6 nut 

(G)

.

5.2.7.    Check that the assembled frame is square and tighten all the fasteners. repeat the procedure for the second frame assembly. 

 

5.3.     fIttING tHe croSS BeaMS: refer to (fig.2).

5.3.1.    Support one end frame in a vertical position and attach the end of 

   one cross beam 

(I)

 to it at the base of one of the uprights 

(a)

.  

  ensure that both tags on the end bracket engage properly with  

  the slots in the upright as shown in the inset diagram.  

  Tap the cross beam gently next to the end bracket so that the beam  

  is properly seated into the slots in the upright. Insert the locking  

 pin 

(H)

 so that it is against the beam. Connect the other end of the  

  beam to the second end frame at the same height, tap into place  

  and secure with a locking pin 

(H)

.

5.3.2.    Attach another cross beam 

(I)

 to the other side of the end frames  

  ensuring that it is at the same level as the first cross beam.

5.3.3.    See  (fig.3).

 

Continue to assemble the next two pairs of cross beams  

 

(I)

 at the heights required. The end frames allow adjustment in 2”  

  increments. each pair of beams must be mounted at the same  

  height. ensure that all tabs on the cross beam brackets are fully  

  engaged in the slots in the uprights and that the cross beams are  

  properly tapped down into place then secured with a locking pin 

(H)

.

5.3.4.    extra components are available to create extra storage racks as  

  required (see Section 3). 

6.  INtroDuctIoN

extension unit for model no. STr600. Supplied as three pairs of cross beams and a single upright in order to reduce cost when looking to build 

multiple tyre racks. Stores up to 26 tyres, 13 per level, with a total capacity of 400kg (200kg/level) when used with model no. STr600.

7.  SPecIfIcatIoN

Model No: ...............................................................Str006e

overall size (W x d x H): .....................1950 x 455 x 2000mm

maximum capacity: .................................... 400kg (200kg/level)

Beam width: .................................................................1840mm

Original Language Version

© Jack Sealey limited

STr600, STr600e | Issue 5 (H,F) 03/12/19

two level tyre rack eXteNSIoN 200kG caPacIty Per level

   

model no:

 Str600e

fig.2

fig.3

Reviews: