DELUXE FACE SHIELD WITH POWERED AIR
PURIFYING RESPIRATOR (PAPR)
MODEL NO:
SSP80PAPR
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
TANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH
HE
P
PR
O
ODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE
ER
S
SON
NAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL
SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with
all electrical products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance
Test)
tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is
fi
tted with the
correct fuse - see fuse rating in these instructions.
DO
NOT
pull or carry the appliance by the power cable.
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a
fi
rm grip on the plug.
DO
NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
quali
fi
ed electrician.
1.1.4.
This product is
fi
tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a quali
fi
ed electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO
NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a quali
fi
ed electrician.
1.2. GENERAL
SAFETY
Ensure all workshop safety rules, regulations and conditions are complied with when using this equipment. The face shield will
not
o
ff
er protection against misuse of workshop tools, equipment, or accessories.
Maintain the face shield in good condition and protect cartridge from liquid and dirt contact.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Fit the face shield and adjust the head band so the face shield will sit as low and near to your face as possible.
Ensure that the face hood is securely attached to the face shield.
Use face shield only in temperatures ranging from -5°C to 55°C.
Remove
ill
fi
tting clothing, remove ties, watches, rings and other loose jewellery.
Maintain correct balance and footing.
Ensure
the
fl
oor is clear from obstructions, not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working area.
Use of this face shield is for face and eye protection against low energy impact and splashing liquids.
Inspect the face shield frequently as a pitted or scratched face shield reduces vision and therefore should be replaced immediately.
Be aware if wearing standard ophthalmic spectacles they may transmit impacts, creating a hazard for the user.
DO NOT
use if any part of the face shield is cracked or broken.
DO NOT
place this product on a hot surface.
DO NOT
use this face shield for protection against gases, ultra violet or infra red radiation, ionising radiation, liquids under
pressure or other severe hazards.
DO NOT
use this face shield against heavy impact hazards, the lens is breakable.
DO NOT
use this face shield for welding or laser cutting.
DO NOT
use face shield for any purpose for which it is not designed.
WARNING! DO NOT
use the face shield if damaged or you suspect it may be faulty. (Contact Sealey Stockist).
Recommended fuse rating
3 Amp
SSP80PAPR Issue 1 11/08/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Charger indoor
use only
