4.3.7.
Refer to the Settings and Layouts for Cutting table and position the
fi
rst work piece as listed.
4.3.8.
Place
the
fi
rst work piece onto the compound mitre saw and perform the cut.
4.3.9.
Refer to the Settings and Layouts for Cutting table to reset the compound mitre saw position for the second cut.
4.3.10.
Place the second work piece onto the compound mitre saw and perform the cut.
WARNING!
Read and understand the compound mitre saw instructions.
NOTE:
Prior to cutting your work piece perform practice cuts on smaller scrap pieces.
SMS7P Issue 1 16/11/21
Original Language Version
© Jack Sealey Limited
COMPOUND CUT CONVERSION TABLE
Mitre
Cut
38º Crown
45º Crown
Mitre
Cut
38º Crown
45º Crown
Mitre
Angle
Bevel
Angle
Mitre
Angle
Bevel
Angle
Mitre
Angle
Bevel
Angle
Mitre
Angle
Bevel
Angle
1
0.6
0.8
0.7
0.8
31
20.3
23.9
23.0
21.4
2
1.2
1.6
1.4
1.4
32
21.0
24.7
23.8
22.0
3
1.9
2.4
2.1
2.1
33
21.8
25.4
24.7
22.7
4
2.5
3.2
2.8
2.8
34
22.6
26.2
25.5
23.3
5
3.1
3.9
3.5
3.5
35
23.3
26.9
26.3
23.9
6
3.7
4.7
4.3
4.2
36
24.1
27.6
27.2
24.6
7
4.3
5.5
5.0
4.9
37
24.9
28.3
28.1
25.2
8
5.0
6.3
5.7
5.7
38
25.7
29.0
28.9
25.8
9
5.6
7.1
6.4
6.4
39
26.5
29.7
29.8
26.4
10
6.2
7.9
7.1
7.1
40
27.3
30.4
30.7
27.0
11
6.8
8.7
7.8
7.8
41
28.2
31.1
31.6
27.6
12
7.5
9.4
8.6
8.5
42
29.0
31.8
32.5
28.2
13
8.1
10.2
9.3
9.2
43
29.9
32.5
33.4
28.8
14
8.7
11.0
10.0
9.9
44
30.7
33.2
34.3
29.4
15
9.4
11.8
10.7
10.6
45
31.8
33.9
35.3
30.0
16
10.0
12.5
11.5
11.2
46
32.5
34.5
36.2
30.6
17
10.7
13.3
12.2
11.9
47
33.4
35.2
37.2
31.1
18
11.3
14.1
12.9
12.6
48
34.4
35.9
38.1
31.7
19
12.0
14.9
13.7
13.3
49
35.3
36.5
39.1
32.3
20
12.6
15.6
14.4
14.0
50
36.3
37.1
40.1
32.8
21
13.3
16.4
15.2
14.7
51
37.2
37.8
41.1
33.3
22
14.0
17.2
15.9
15.4
52
38.2
38.4
42.2
33.9
23
14.7
17.9
16.7
16.0
53
39.3
39.0
43.2
34.4
24
15.3
18.7
17.5
16.7
54
40.3
39.6
44.2
34.9
25
16.0
19.5
18.3
17.4
55
41.3
40.2
45.3
35.4
26
16.7
20.2
19.0
18.1
56
42.4
40.8
46.4
35.9
27
17.4
21.0
19.8
18.7
57
43.5
41.4
47.4
36.4
28
18.1
21.7
20.6
19.4
58
44.6
4.9
48.5
36.8
29
18.8
22.5
21.4
20.1
59
45.7
42.5
49.6
37.3
30
19.6
23.2
22.2
20.7
60
46.8
43
50.8
37.8
SETTINGS AND LAYOUT FOR CUTTING CROWN MOULDING WITH A
COMPOUND MITRE SAW
INSIDE CORNER
LEFT PIECE
RIGHT PIECE
Mitre swing:
RIGHT
Mitre swing:
LEFT
Bevel swing:
LEFT
Bevel swing:
LEFT
Work piece location:
LEFT of BLADE
Work piece location:
LEFT of BLADE
Moulding edge against fence:
TOP
Moulding edge against fence:
BOTTOM
OUTSIDE CORNER
LEFT PIECE
RIGHT PIECE
Mitre swing:
LEFT
Mitre swing:
RIGHT
Bevel swing:
RIGHT
Bevel swing:
RIGHT
Work piece location:
RIGHT of BLADE
Work piece location:
RIGHT of BLADE
Moulding edge against fence:
BOTTOM
Moulding edge against fence:
TOP
fi
g.2
fi
g.3
