© Jack Sealey Limited
Original Language Version
SM750 Issue No.1 27/11/12
Always work in a well ventilated area. Whenever possible use
the dust collection outlets provided on the machine.
Take care that the belt and disc sander cannot tip over or move
while sanding long or heavy objects. If necessary, fasten the
belt and disc sander to a supporting surface.
Ensure that the sanding belt is running in the correct direction
and ensure that the sanding disc or sanding belt is not
damaged.
DO NOT
allow children or untrained persons to operate the
sander. Keep them away from the work area.
Ensure the sanding belt is correctly positioned and adjusted so
that it cannot run off the pulleys.
DO NOT
remove the safety guard whilst sander is in use.
Remove ill fitting clothing, ties and loose jewellery and tie back
long hair. Keep hands and body clear of the worktable when
operating the sander.
DO NOT
use the belt and disc sander near flammable liquids,
gases or dust.
DO NOT
disassemble the machine and do not try to repair it
yourself. Have the unit repaired by a professional or contact
your local Sealey dealer. Always use original replacement parts.
DO NOT
touch the sanding belt immediately after operation; it
may be extremely hot and cause burns. The sanding belt is
sharp-edged.
DO NOT
use excessive force against the sanding belt or disc.
DO NOT
operate the sander when you are tired, under the
influence of alcohol, drugs or intoxicating medication.
DO NOT
get the sander wet or use in damp or wet locations or
areas where there is condensation.
DO NOT
switch the sander on while the workpiece is in
contact with the abrasive and
DO NOT
leave the sander
running unattended.
2. INTRODUCTION
3. TECHNICAL SPECIFICATION
Model No:
.................................................................................
SM750
Belt Size: ...........................................................................25 x 762mm
Belt Speed: ..........................................................................845mtr/min
Disc Size: ..................................................................................125mm
Disc Speed: ............................................................................ 2850rpm
Table Size: .......................................................................128 x 185mm
Table Tilt: ......................................................................................0-45°
Motor Power: ................................................................... 250W - 230V
Supply:.......................................................................................... 230V
Dust Extraction: ..................................................................2 x Ø45mm
Weight: .........................................................................................7.4kg
Replacement Sanding Belts:
..............................................................
Model No:
.................................................................................
Grade:
SM750B60G ............................................................. (Pack of 5) 60Grit
SM750B80G ............................................................. (Pack of 5) 80Grit
SM750B120G ......................................................... (Pack of 5) 120Grit
Replacement Sanding Discs:
.............................................................
Model No:
.................................................................................
Grade:
SM750D80G ................................................................................80Grit
Bench mounting semi-portable belt and disc sander suitable for
general woodworking applications. Powerful induction motor with
smooth, bearing-mounted drive pulleys gives quiet operation. Sanding
disc table tilts to 45° and is supplied with mitre gauge for accurate
angle sanding. Sanding belt is positioned vertically.
fig.1
1 Cover clamp knob
2 Clear protective cover
3 Vertical sanding belt
4 Adjustable sanding table
5 Table locking lever
6 Lever fixing screw
7 Disc table clamp knob x 2
8 Adjustable angle guide
9 Dust exhaust outlet x 2
10 Sanding disc table
11 Sanding disc
12 On/Off switches
13 Sanding belt tracking knob
14 Table levelling screw
15 Belt cover fixing screw
4. ASSEMBLY & ADJUSTMENT
4.2 Attaching the sanding disc table.
4.2.1 On each inner mounting face of the sanding table adjustment
scales there is a spigot which acts as a hinge point when
adjusting the angle of the table. See fig.3(P). Hold the sanding
table (T) in the position shown in fig.3 above, slide the
WARNING!
Ensure that the sander is disconnected from the
mains power supply before beginning assembly.
4.1 Attaching the sanding disc dust extractor.
4.1.1 Attach the dust extractor plate (E) over the lower part of the
sanding disc using the four screws provided as shown in fig.2.
fig.3
fig.2
