Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging
should be sorted, taken to a recycle centre and disposed of in
a manner which is compatible with the environment.
WEEE REGULATIONS.
Dispose of this product at the end of
its working life in compliance with the EU Directive on Waste
Electrical and Electronic Equipment. When the product is no
longer required, it must be disposed of in an environmentally
protective way.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
6.1 PREPARATION.
6.1.1. If the sander is to be used in a temporary work environment ensure that the rubber feet are attached in order to keep it stable in use.
Wear suitable respiratory protection.
6.1.2. The sander can also be permanently installed in a workshop environment by removing the feet and bolting the unit to a bench using
the same fixing holes as used for the feet. Ideally the sander should be connected to a dust extraction system or vacuum cleaner.
6.1.3.
DO NOT
allow two people to use the sander at the same time.
6.2.
Dust extraction.
6.2.1. Both the belt and the disc are provided with dust extraction ports for connection to a workshop extractor system or a vacuum cleaner
and it is recommended that these facilities be used if they are available.
6.2.2. If no extraction facilities are available you must wear suitable respiratory protection. Contact you local Sealey dealer for a full range of
protective equipment (PPE).
6.3.
Adjusting (tracking) the sanding belt.
6.3.1. The sanding belt supplied with the machine is factory set to run in alignment with the drive wheels. Should the belt begin to run out of
true it can be re-centred using the tracking knob shown in fig.7 (C). Turn the knob clockwise to move the belt to the right, (when facing
the machine). Turn the knob counter clockwise to move the belt to the left.
6.4. Sanding
6.4.1. Adjust the angle of the appropriate table and/or guide as required by the job in hand.
6.4.2. Plug the sander into the mains power supply.
6.4.3. Switch on the sander using the green oN button. See fig.1(12).
6.4.4.
Remember that even though you are using only one of the sanding facilities, the other is still turning and could represent a
hazard to you or other people nearby.
6.4.5. Allow the belt or disc to reach full speed before bringing the workpiece into contact with it.
DO NOT
use excessive force to remove
material but allow the abrasive material to do its job.
6.4.6. Switch off the sander using the red oFF button. See fig.1(12).
6.4.7. Allow the disc and belt to come to a standstill before leaving the sander.
6.4.8.
DO NOT
leave the sander running unattended.
6.4.9. Unplug the sander from the mains power supply when no longer required.
6. OPERATION
7. MAINTENANCE
7.1
In
daily use keep the sander clean with an air line and dry cloth or brush.
7.2.
Annually remove the side cover and remove internal accumulation of dust and ingress with an air line, vacuum cleaner or brush.
7.3.
Visually check for belt and disc wear before each use, replacing at the first sight of damage.
7.4.
Switch the sander off when not in use or unattended.
7.5.
Any other maintenance outside the scope of above to be carried out by a competant technician.
© Jack Sealey Limited
Original Language Version
SM750.V2 Issue No.1 - 08/06/15
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
