background image

1.1. 

ELECTRICAL SAFETY

  

WARNING!

 It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other 

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A 

Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current 

Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected 

by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. 

You must also read and understand the following instructions concerning electrical safety.

1.1.1. The 

Electricity at Work Act 198

9 requires that all portable electrical appliances, if used on business premises, are tested by a  

 

 

qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The 

Health & Safety at Work Act 1974

 makes owners of electrical appliances responsible for the safe condition of those appliances  

 

and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3.  Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.    

 

and use a Portable Appliance Tester.

1.1.4.  Ensure that cables are always protected against short circuit and overload.

1.1.5.  Regularly inspect power supply cables and plugs for wear or damage and check all  

 

 

connections to ensure that none is loose.

1.1.6. 

Important:

 Ensure that the voltage marked on the appliance matches the power supply 

 

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. 

DO NOT

 pull or carry the appliance by the power cable.

1.1.8. 

DO NOT

 pull the plug from the socket by the cable.

1.1.9. 

DO NOT

 use worn or damaged cables, plugs or connectors. Immediately have any faulty 

 

item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is  

 

 

damaged, cut the cable just above the plug and 

dispose of the plug safely

 

Fit a new plug according to the following instructions (UK only).

 

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 b) 

Connect the BROWN live wire to the live terminal ‘L’.

 

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

 

d) After wiring, check that there are no bare wires, that all wires have been correctly    

 

connected, that the cable outer insulation extends beyond the cable restraint and that the  

 

restraint is tight.

 

Double insulated products, which are always marked with this symbol      , are fitted with live (brown) and neutral (blue) wires only.    

 

To rewire, connect the wires as indicated above - 

DO NOT

 connect either wire to the earth terminal.

1.1.10.  Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure  

 

that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and  

 

 

socket with your electrician.

1.1.11.  If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance    

 

plugged into it will be protected. The cable core section is important and should be at least 1.5mm2, but to be absolutely sure that the  

 

capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use   

 

of 2.5mm2 section cable.

RECOMMENDED

 FUSE RATING: 5 AMP

© Jack Sealey Limited

Original Language Version

SM750.V2     Issue No.1 -  08/06/15

1.2. 

GENERAL SAFETY

 

WARNING! 

Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.

 

WARNING! 

Disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.

 

WARNING! DO NOT 

sand any materials containing asbestos.

 

Ensure the operating voltage stated on the ratings plate corresponds to your mains power supply.

 

Check the belt and disc sander and the electrical connections for any damage and 

DO NOT

 use the tool if the sander or the cable is    

 damaged.

 

Ensure that the belt and disc sander is switched off before plugging in to the mains power supply.

 

Persons with limited physical, sensory or mental abilities are not allowed to use the unit, unless they are fully supervised and briefed on  

 

safety issues by a qualified person.

 

Use the belt and disc sander according to this manual and only for the purpose for which it is designed.

 

Before starting up, make sure that no spanners or adjusting keys are attached to the machine.

 

Avoid contact with grounded surfaces such as radiators, pipes etc.

 

Maintain correct balance and footing, ensure that the floor is not slippery and wear non-slip rubber soled footwear.

INSTRUCTIoNS FoR: 

BELT/DISC SANDER 25 X 762

MM

 / Ø125

MM

250W / 230V

MoDEL No:

 SM750.V2

 1.  SAFETY

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE 

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

Refer to the instuctions manual booklet

Wear a mask

Wear eye protection

Wear ear protection

Wear protective gloves

Reviews: