2. APPLICATION & sPECIFICATION
Portable power planer with heavy-duty cast base for accurate and smooth planing. Accurate fence tilts between 45° and 90°. fitted with two
blades capable of planing timber up to 150mm wide. no-volt release switch prevents uncontrolled re-start after power interruption. Dust
extraction port with collection bag. Adjustable cutting depth up to 3mm.
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100W, 230V 50Hz.
Maximum cut (width x depth) . . . . . . . . . . . . . . . . . . . . . . . 150 x 3mm
cutter-head speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10000rpm
fence Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45-90°
Working table size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 x 160mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17kg
3.1
AssEmBLY
WARNING! DO NOT
plug the planer into the mains power
supply until completely assembled.
DO NOT
allow brake fluids, petroleum, penetrating oils etc. to
come into contact with plastic parts of planer as damage may
result. the machine is shipped nearly complete in one carton.
Additional parts which need to be fastened to machine should
be located and accounted for before assembling. (
fig. 1
).
A.
Planer
B.
Angle fence
c.
4mm Hex wrench
D.
5mm flat washer
E.
5mm Lock washer
f.
Hex head bolt
G.
Bag clamp
H.
Dust collection bag
3.2
sETTING ANGLE FENCE (fig. 2)
3.2.1 Insert screw into the slot (A), then locate the fence on screw
(c). securely tighten screw (A) first, then screw (c).
Angle adjustment is made by loosening knob (D) and
tilting fence to the desired angle using scale (B). re-tighten
knob (D)
fig. 2
.
3.3
sETTING sAFETY GUARD (fig. 3)
3.3.1 to adjust the height of the guard, loosen knob A, raise
or lower the guard (B), until it is in firm sliding contact with the
workpiece. tighten knob A.
3.3.2 After adjusting the guard height it can be adjusted sideways
to set the required stock width for jointing. (As in fig.4)
AttEntIon: Make sure that the switch is in off position before
adjusting the cutting depth, replacing or adjusting the blades. Make
sure the blade screws are securely tightened.
3. AssEmBLY
A
B
c
D
E
f
G
H
fIG. 1
A
B
c
D
A
B
fIG. 2
fIG. 3
Original Language Version
sM1310 Issue: 2 - 23/11/09
When planing short workpieces, a push-stick should be used.
check for alignment of moving parts, binding of moving parts, mounting and any other conditions that may affect it's operation.
If a guard or other part is damaged it should be properly repaired or replaced by an authorized service centre unless otherwise indicated in
this instruction manual.
stay alert
- Watch what you are doing, use common sense and do not operate the tool when you are tired.
When not in use switch off the planer and remove plug from the power supply.
NOTE!
Max. allowable blade projection over cutterblock 1.0mm/0.004 inch +10%.
