instructions for
torque wrenches
model no:
s0455.V2 & s0456.V2
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. sAFetY
9
9
9
ensure all workshop safety rules, regulations and conditions are complied with when using the torque wrench.
9
9
99
maintain the
wrench in good condition and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts
may be dangerous and will invalidate the warranty.
9
9
99
the wrench is a precision tool,
Do not
abuse it.
9
9
99
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
9
99
Keep children and unauthorised persons away from the working area.
wArnInG! Do not
use the wrench if damaged or thought to be faulty (contact service Agent).
9
8
9
Do not
drop or throw the wrench.
9
8
9
Do not
use wrench unless you have been instructed in its use by a qualified person.
9
8
99
Do not
use any cleaner which might affect the high pressure grease with which the wrench it is packed.
9
After use adjust to lowest torque setting (but not below),clean and store in a safe, dry, childproof location.
2.
i
IntroDuctIon
Heat treated steel ratchet head. fully hardened and tempered. chrome plated for corrosion resistance. micrometer type torque range
adjustment. twist reverse ratchet mechanism. supplied in storage case.
3.
i
specIFIcAtIon
model no: ...................................................................s0455.V2
drive type: ......................................................................3/8”sq.
length: ..........................................................................365mm
range: ....................................................19-110nm (14-81lb.ft)
model no: ...................................................................s0456.V2
drive type: ......................................................................1/2”sq.
length: ..........................................................................440mm
range: ................................................. 42-410nm (40-155lb.ft)
4.
i
operAtIon
4.1.
Hold torque wrench in left hand (if right handed) so that required scale is uppermost and visible.
4.2.
turn knurled lock screw at end of handle anticlockwise to unlock knurled adjusting grip.
4.3.
turn adjusting grip to select torque setting as follows, for a required setting of 50nm:
•
Turn grip until top edge of grip is level with the 47Nm line on the handle scale and the zero graduation on the grip is aligned with the
centre line of the handle scale.
•
Rotate handle further, clockwise, until ‘3rd’ graduation on grip is aligned with centre line to give a setting of 47 + 3 = 50Nm.
note:
If using the ‘kgm’ scale then each division on the grip graduation is equivalent to 0.98Nm.
therefore to set wrench at 4.5kgm:
•
Turn grip until top edge of grip is level with the 4.0kgm line on the handle scale and the zero graduation on the grip is aligned with the
centre line of the handle scale.
•
Rotate the handle further, clockwise, until the ‘5th’ graduation on the grip is aligned with the centre line to give a setting of = 4.5kgm.
4.4.
tighten lock screw at end of handle to prevent accidental alteration of the setting.
When tightening the nut/bolt you will feel and hear the wrench mechanism click when the set torque is reached.
immediately stop applying force to wrench to avoid overtightening nut/bolt. Wrench will reset ready for next application.
4.5.
Do not
turn the handle below its lowest torque setting.
note:
if the wrench has not been used for some time, operate it a few times, at a low setting, to ensure all internal parts are coated in
grease.
5.
i
cAlIbrAtIon
5.1.
If the user does not utilize a control procedure, a period of 12 months, or 5000 cycles, whichever occurs first, may be taken as
default values for the interval between calibrations. The interval starts with the first use of the torque tool. Shorter intervals between
calibrations may be used if required by the user, their customer or by legislation.
s
0455.V2, S0456.V2 | Issue:1 07/06/17
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear eye
protection
