8
dO nOT
get the grinder wet or use in damp or wet locations.
8
dO nOT
switch the grinder on whilst the disc is in contact with the work piece.
8
dO nOT
cover the grinder air vents. to do so will overheat the machine.
8
dO nOT
touch the work piece immediately after grinding as it will be very hot.
8
dO nOT
use the grinder as a fixed tool, and
dO nOT
try to cool the grinding discs with water or other lubricants.
8
dO nOT
hold unsecured work in your hand and
dO nOT
touch the grinding disc whilst operating, or whilst plugged into the mains
power.
8
dO nOT
leave the grinder running unattended and
dO nOT
lay the grinder down whilst it is running.
8
dO nOT
operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9
When not in use, switch off grinder, remove plug from power supply and store in safe, dry, childproof area.
wArning!
the grinding process can produce streams of sparks (especially when grinding metal) which are a potential source of
ignition.
8
dO nOT
use the grinder where there are flammable liquids, solids or gases.
8
dO nOT
allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. fabrics
contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
9
to reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
preference to man-made fibres.
wArning!
– risk of Hand Arm Vibration injury.
this tool may cause Hand Arm Vibration syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
this tool is to be operated in accordance with these instructions.
measured vibration emission value (a): ..........
5.30 m/s²
uncertainty value (k): ........................................
1.5 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We
recommend that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
such factors include; the operator, the task and the inserted tool or consumable.
NB:
ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
the state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand
Arm Vibration syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can
be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm
and dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to
the correct use and maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be
found on the HSC website. www.hse.gov.uk - Hand-Arm Vibration at Work.
2. inTrOducTiOn
s
lim ergonomic body ensures a firm grip while performing various tasks. Features heavy-duty alloy bevel gear head with composite body
casing and spindle lock for fast loading/unloading of discs. 750W motor develops powerful 12000rpm (no load speed). Supplied with side
handle, guard and spanner. Fitted with 2mtr power cable and BS approved plug. Cutting disc not included, order Model No. PTC/115C.
3. specificATiOn
model no. ..................................................................sGs115
disc size ..................................................................Ø115mm
spindle size ........................................................
M14 x 2mm
motor Power ..................................................................
750W
supply ............................................................................
230V
no load speed ........................................................
12000rpm
W
eight ........................................................................... 1.8kg
4. OperATiOn
4.1.
Before use
4.1.1.
Always check the mains supply voltage before use! it must correspond with the rating label on the appliance.
4.1.2.
remove any packing material and loose parts from unit.
4.2.
disc guard
wArning!
the grinder should be used only with guard.
4.2.1.
the position of the disc guard can be adjusted to suit the working conditions.
4.2.2.
to adjust the disc guard.
Loosen the bolt clamping the guard, turn the guard to the desired position, re-tighten the bolt firmly.
wArning!
the closed disc guard should always point towards the user to protect him from sparks and chippings.
4.3.
Auxiliary handle
wArning!
the machine should be used only with both handles.
4.3.1.
depending on the working method, the auxiliary handle can be mounted in two different positions on the grinding head.
8
dO nOT
continue to use an auxiliary handle if it is damaged.
8
s
GS115 | Issue 1 28/10/16
Original Language Version
© Jack sealey limited
