background image

SUBFRAME/ENGINE LOAD ADAPTOR FOR 
TTJ TRANSMISSION JACKS 

MODEL NO: 

SFC01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 
instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

‰

 

 WARNING! 

The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions

 

and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this

 

product, but must be applied by the operator.

 

‰

  

WARNING!

 Ensure all preliminary checks are carefully carried out before use and that all fixings are correctly and securely engaged.  

 

Immediately repair or replace damaged parts (use authorised service agent). Ensure use of genuine parts only. 

 

Unauthorised parts may be dangerous and will invalidate the warranty.

 

‰

  

WARNING!

 Use jack on level and solid ground, preferably smooth concrete. Ensure the floor over which the loaded jack will be    

 

transported is swept clean.

 

‰

  

WARNING!

 Ensure that the loaded item is correctly supported, well balanced and secured in place prior to final removal from vehicle  

 

and before any movement of the loaded jack within the workshop.

 

8

  

DO NOT 

make any modifications to the unit supplied.

 

  

DANGER

DO NOT

 use on tarmacadam, or any other soft surface as jack may sink or topple. Serious injury may result if ignored.

 

  

DANGER

! If the load tips or leans, stop what your are doing. MOVE QUICKLY TO A SAFE DISTANCE. 

DO NOT

 TRY TO HOLD

 

OR STEADY JACK.

 

9

  

The unit is intended for use only with Sealey products 500TTJ and 800TTJ.

 

9

   Ensure that load adaptor is correctly attached to the jack and that the grub-screw is fitted before use. 

2.  INTRODUCTION

F

ully adjustable SFC01 Subframe/Engine support adaptor that is supplied with various designs of fittings to suit different applications. 

Designed to assist in the removal and fitting of subframes, complete engine assemblies, rear axles, gearboxes, fuel tanks, exhaust systems 

and other awkward loads. The adaptor easily fits directly on to the Sealey 500TTJ and 800TTJ Transmission Jacks and assists in allowing 

awkward two or three man jobs to be carried out by one person. 

3.  SPECIFICATION

Model No.:.................................................................. SFC01

Capacity ....................................................................... 450kg

4.  ASSEMBLY

4.1.    

Thread the boss located on the underside of 

 

the Load Plate onto the Jack ram. Fix in place 

 

using the grub screw supplied when fully 

 engaged.

4.2.    

Thread M16 Stud and Hex nut (fig.1) into load

  

plate such that underside of the nut rests

 

on the surface of the Load Plate and that the 

 

stud is flush with the nut.

4.3.    

Slide the Support arm guide over the stud and 

 

screw the Support arm hand wheel onto it.

4.4.    

Screw the Tool post and hand wheel assembly

 

into the Support arm.

M16 Stud bar 

and Hex. nut

Tool post and
Hand wheel

Support arm
Hand wheel

Support arm
Guide

SFC01      Issue 1    12/01/22

Original Language Version

© Jack Sealey Limited

Refer to 

instructions

 Wear protective 

gloves

 Wear safety 

footwear

Load Plate

   fig.1

Reviews: