4. OPERAtiON
Aluminium cylinders with cast iron liners give reduced weight and
improved resistance to wear. suitable for general-purpose workshop
applications. Pump head directly coupled to heavy-duty induction
motor for reliable operation. Precision welded receiver tank
manufactured to meet Pressure Vessel directive 87/404/eec. fitted
with fully automatic pressure cut-out switch, air regulator and tank
and supply pressure gauges. supplied with handle and wheels for
easy manoeuvrability. fitted with AstA/Bs approved non-rewirable
plug.
3. PREPARAtiON
3.1.
remove compressor from packaging and inspect for any
shortages or damage. If anything is found to be missing or
damaged contact your supplier.
3.2.
save the packing material for future transportation of the
compressor. We recommend that you store the packing in a
safe location, at least for the period of the guarantee. then, if
necessary, it will be easier to send the compressor to the
service centre.
3.3.
confirm that the mains voltage corresponds with the voltage
shown on the compressor data plate.
3.4.
Assemble the wheels (fig.A.X) and rubber feet (fig.A.Y) to
the main frame using using the nuts, bolts and washers
supplied.
3.5.
the compressor should be operated on a flat surface, or one
that does not exceed 10° either transversely or longitudinally
(fig.1), and should be in a position that allows good air
circulation around the unit.
3.6.
remove the plastic transit plug from the oil filler hole.
3.7.
Before using the compressor check the oil level by referring
to the oil sight glass (fig.2c). If the oil level is not up to the
red centre mark it should be further topped up with
recommended oil (see section 5.7). screw the filler/breather
cap into the aperture as shown in fig.2B.
3.8.
screw the back half of a filter unit into the downward facing
port openings in each head as shown in fig.2.A. Place a filter
cover over each threaded rod protruding from the back half
of the filter and secure each with a wing nut. refer also to
fig.4.
fig.2
WARNiNG! Ensure that you have read, understood and
apply Section 1 safety instructions.
4.1. iMPORtANt. the use of extension leads to connect this
compressor to the mains is not recommended as the
resulting voltage drop reduces motor, and therefore
pump, performance and could damage your compressor.
4.2. take care when selecting tools for use with the
compressor. Air tool manufacturers normally express the
volume of air required to operate a tool in cubic feet per
minute (cfm).
fig.A
2. iNtROdUCtiON & SPECiFiCAtiON
3
Keep children and unauthorised persons away from the
working area.
7
dO NOt
dis-assemble compressor for any reason. the unit
must be checked by qualified personnel only.
7
dO NOt
use the compressor outdoors, or in damp, or wet,
locations.
7
dO NOt
operate within the vicinity of flammable liquids,
gases or solids.
7
dO NOt
touch compressor cylinder, cylinder head or pipe
from head to tank as these may be hot.
7
dO NOt
use this product to perform a task for which it has
not been designed.
7
dO NOt
deface the certification plate attached to the
compressor tank.
7
dO NOt
cover the compressor or restrict air flow around the
unit whilst operating.
q
dANGER! dO NOt
direct the output jet of air towards
people or animals.
7
dO NOt
operate the compressor without an air filter.
7
dO NOt
allow anyone to operate the compressor unless
they have received full instructions.
WARNiNG!
the air tank is a pressure vessel and the
following safety measures apply:
7
dO NOt
tamper with the safety valve,
dO NOt
modify or
alter the tank in any way and
dO NOt
strap anything to the
tank.
7
dO NOt
subject the tank to impact, vibration or to heat and
dO NOt
allow contact with abrasives or corrosives.
3
drain condensation from tank daily.
WARNiNG!
If an electrical fuse blows, ensure it is
replaced with an identical fuse type and rating.
3
When not in use, store the compressor carefully in a safe,
dry, childproof location.
MOdEL
............................................................................
SAC5030vE
Motor output
..............................................................................3.0hp
voltage/phase
...................................................................230V - 1ph
Rated supply
.................................................................................13A
Noise level
................................................................................97lwA
Air displacement
....................................................... 11.6cfm-328l/m
Maximum free air delivery
..........................................8.1cfm-230l/m
tank capacity
...............................................................................50ltr
Max pressure
.................................................................116psi / 8bar
Weight
..........................................................................................37kg
dimensions (W x d x H)
.....................................660 x 420 x 650mm
fig.1
sAc5030Ve Issue no: 3 - 25/06/12
Original Language Version
© Jack sealey limited
