![background image](http://html1.mh-extra.com/html/sealey/sa722-v2/sa722-v2_instructions_1226581001.webp)
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
MINI AIR ANGLE ORBITAL
POLISHER
MODEL No:
SA722.V2
1. SAFETY INSTRUCTIONS
Original Language Version
SA722.V2 Issue: 1 - 17/10/11
Composite lightweight housing reduces effects of chill
on operator’s hands. Adjustable speed control on side
of motor housing. Air motor with quality bearings for
smooth and powerful operation. Integral gear system
reduces output speed, still maintaining a high torque
level. Supplied with Ø75mm hook-and-loop pad for use
with buffing and polishing heads.
2. INTRODUCTION & SPECIFICATION
Pad Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75mm
Motor Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.3hp
Free Speed . . . . . . . . . . . . . . . . . . . . . .2000-6000rpm
Operating Pressure . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption . . . . . . . . . . . . . . . . . . . . . . . . . 3cfm
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Noise Power . . . . . . . . . . . . . . . . . . . . . . . . . . 89.4dB.A
Noise Pressure. . . . . . . . . . . . . . . . . . . . . . . . 78.4dB.A
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6kg
1.1. Operational Safety
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the
polisher in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
3
Use in a suitable clean and tidy work area and ensure there is adequate lighting.
3
Before each use check pads for condition. If worn or damaged replace immediately.
3
Ensure the pad rating is the same as, or, greater than the RPM rating of the polisher.
3
Ensure there are no flammable or combustible materials near the work area.
p
WARNING!
Always wear approved eye or face and hand protection when operating the polisher.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back
long hair.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the polisher. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure - 90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this polisher poses a health risk. It is the owner’s responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT
use the polisher for a task it is not designed to perform.
7
DO NOT
operate polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING!
DO NOT
polish any materials containing asbestos.
7
DO NOT
carry the polisher by the hose, or yank the hose from the air supply.
7
DO NOT
force, or apply heavy pressure to the polisher, let the polisher do the work.
7
DO NOT
place air line attachments close to your face and
DO NOT
point at other persons or animals.
7
DO NOT
operate polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT
use polisher where there are flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
7
DO NOT
carry the polisher with your finger on the power lever.
7
DO NOT
direct air from the air hose at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.