WARNING!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is toxic and
must therefore be avoided. The following action must be taken before using the sander on a surface that you suspect may have
contained lead in the paint.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
DANGER!
Keep all persons and pets away from the working area. The following persons are particularly vulnerable to the effects of
lead paint dust:
Expectant women, babies, and children.
We recommend personal protection by using the following safety items:
a
) Paint Spray Respirator (Our ref SSP1699)
b
) PE Coated Hooded Coverall (Our ref SSP265-L).
c
) Latex Gloves (Our ref SSP24).
Take adequate measures to contain the paint dust, flakes, and scrapings.
Continue to wear safety equipment as above, and thoroughly clean all areas when task is complete. Ensure paint waste is disposed of in
sealed bags or containers.
INSTRUCTIONS FOR:
AIR MINI SANDER KIT 50mm 35pc
MODEL NO:
SA720.V2
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years
of trouble free performance.
1.
SAfETy INSTRucTIoNS
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
WARNING!
Disconnect from air supply before changing accessories, servicing or maintenance.
WARNING!
Always wear approved eye or face protection when operating the sander.
WARNING!
Ensure correct air pressure is maintained and does not exceed 90psi
WARNING!
DO NOT sand any materials containing asbestos.
DO NOT use sander for a task it is not designed to perform.
DO NOT operate if any part is damaged or missing as this may cause failure and/or possible personal
injury.
DO NOT carry the sander by the hose, or yank the hose from the air supply.
DO NOT get the sander wet or use in damp or wet locations.
DO NOT use this sander with water. This model is only for dry use.
DO NOT place attachments close to your face and do not point at other persons or animals.
DO NOT operate sander if you are tired or under influence of alcohol, drugs or intoxicating medication.
DO NOT use where there are flammable liquids, solids or gases (paint solvents), waste or wiping rags etc.
DO NOT leave the sander operating whilst unattended.
DO NOT carry the sander with your finger or hand on the power lever.
DO NOT direct air from the air hose at yourself or others.
Maintain the sander in good condition and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
Use sander in a suitable work area, keep area clean, tidy and free from unrelated materials. Ensure there is adequate lighting.
Before use check abrasive pads for condition. If worn or damaged replace immediately.
If dust is generated, use face and or respiratory protection according to COSHH regulations.
Depending on task, sander noise may exceed 85dB in which case wear safety ear defenders.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/ or tie back long hair. Wear appropriate
protective clothing.
Keep hands and body clear of the sanders working parts.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
Ensure workpiece is correctly secured before operating sander. Never hold workpiece by hand.
Check the workpiece to ensure there are no protruding nails, screws, stones, etc.
Avoid unintentional starting.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are
secure.
When not in use disconnect from the air supply and store in a safe, dry, childproof area.
IMPORTANT:
PLEASE READ THESE INSTRucTIoNS cAREfuLLy. NoTE THE SAfE oPERATIoNAL REQuIREMENTS, WARNINGS AND cAuTIoNS. uSE THIS
PRoDucT coRREcTLy AND WITH cARE foR THE PuRPoSE foR WHIcH IT IS INTENDED. fAILuRE To Do So MAy cAuSE DAMAGE AND/oR PERSoNAL
INJuRy, AND WILL INVALIDATE THE WARRANTy. PLEASE KEEP INSTRucTIoNS SAfE foR fuTuRE uSE.
2.
INTRoDucTIoN & SPEcIfIcATIoNS
2.1. Introduction
Designed for smart repair and spot refinishing. 90°Handle configuration with double finger trigger allows unit to fit snugly into palm for
added control. Rubber finger cover reduces effects of chill. Handle exhaust reduces noise and surface contamination. Fitted with variable
speed control. Supplied with selection of 50mm discs and pads with industry standard fitting. Supplied in carry case.
Contents: 50mm Backing Pad; Sanding Discs (10pcs each) - #60, #80, #120grit; 3pcs Surface Preparation Pads (Fine/Medium/Coarse)
2.2 Specification
Free Speed (rpm). . . . . . . . . . . . 15000
Operating Pressure (psi) . . . . . . . . . . .90
Air Consumption (cfm) . . . . . . . . . . . 4
Air Inlet (BSP)+coupling . . . . . . . . . 1/4”
Weight (kg) . . . . . . . . . . . . . . . . . 0.75
Pad Size (mm) . . . . . . . . . . . . . . . . 50
LEAD PAINT WARNING!
SA720.V2 ISSUE No:1 12/01/09
