![background image](http://html.mh-extra.com/html/sealey/sa652-v3/sa652-v3_quick-start-manual_1224934001.webp)
STRAIGHT AIR DIE GRINDER MIDI SIZE
MODEL NO:
SA652.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Follow all workshop Health & Safety rules, regulations and conditions when using tool.
WARNING!
Disconnect from air supply before changing tools or servicing.
9
Maintain die grinder in good condition and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommended 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections
are secure.
WARNING!
Before each use check tool is secure, not worn or damaged. If damaged, replace immediately.
9
Ensure replacement tools are not damaged (cracks, deformations or splinters etc).
9
Always use the correct tool suitable for the material being ground. Ensure the maximum speed specification of the tool is higher than
that indicated on the machine data plate.
WARNING!
Always wear approved eye or face protection when operating the die grinder.
9
Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard. Wear ear defenders and
gloves if necessary.
9
Keep hands and body clear of the workpiece when operating the die grinder.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device.
9
Keep children and non essential persons away from the working area.
9
Avoid subjecting tool to excessive strain, always ease against workpiece (a harsh impact may break the bit). Maintain a
controlled progression.
8
DO NOT
hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
8
DO NOT
use the die grinder for a task it is not designed to perform.
WARNING! DO NOT
use die grinder if damaged or faulty. Contact your local service agent.
8
DO NOT
use die grinder unless you have been instructed in its use by a qualified person.
8
DO NOT
carry the die grinder by the air hose, or pull the hose sharply from the air supply.
8
DO NOT
direct air from the air hose at yourself or others.
WARNING!
DO NOT
grind any materials containing asbestos.
8
DO NOT
turn the die grinder on whilst the tool is in contact with the workpiece.
8
DO NOT
use die grinder where there are flammable liquids, solids or gases such as paint solvents,including waste wiping or cleaning
rags etc as generated sparks may be dangerous.
8
DO NOT
touch the workpiece close to the ground surface as it will be very hot. Allow to cool. The workpiece may also be very sharp.
8
DO NOT
operate die grinder if you are tired, under the influence of alcohol, drugs or intoxicating medication.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Ideal for re-shaping, deburring and smoothing off rough edges on castings. Composite cover moulded around lightweight aluminium alloy
housing, reduces effects of chill on operator’s hands and provides added control. Air motor with quality bearings for smooth and powerful
operation. Exhaust outlet adjusts 360° keeping airflow away from operator. Safety trigger prevents inadvertent operation. Suitable for the
professional workshop.
3. SPECIFICATION
Model No: ............................................................... SA652.V3
Air Consumption:............................................................ 3cfm
Air Inlet Size: .............................................................1/4”BSP
Collet Diameter: .......................................................... Ø6mm
C
onfiguration:
...................................................Straight - Midi
Free Speed: ........................................................... 25000rpm
Length: ....................................................................... 155mm
Noise Power/Pressure: ........................................ 95/84dB(A)
Operating Pressure: ...................................................... 90psi
Vibration/Uncertainty: ....................................... 1.25/0.61m/s²
Refer to
instruction
manual
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
Original Language Version
© Jack Sealey Limited
SA652.V3 Issue:4 (H,F) 15/11/21