InstructIons For:
DIGITAL TYRE INFLATOR WITH TWIN
PUSH-ON CONNECTOR
model no:
SA393
1. SAFETY
3. SPECIFICATION
4. INSTALLATION
2. INTRODUCTION
5. OPERATION
sA393 Issue: 1 - 01/07/14
Original Language Version
© Jack sealey limited
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
disconnect the tyre inflator from the air supply before changing accessories, servicing or performing any maintenance.
Keep children and unauthorised persons away from the work area.
Keep the gauge lcd screen and tyre inflator clean.
replace damaged parts with genuine sealey parts. unauthorised parts may be dangerous and will invalidate the warranty.
check condition of the batteries regularly.
check tyre pressures when they are cold.
D
O NOT
direct the tyre inflator outlet at yourself or others including animals.
D
O NOT
carry the tyre inflator by the hose, or tug the hose from the air supply.
D
O NOT
use the tyre inflator for a task which it is not designed to perform.
D
O NOT
operate the tyre inflator when you are tired or under the influence of intoxicating medicines, drugs or alcohol.
D
O NOT
operate the tyre inflator if parts are missing or the lcd is damaged, this could be dangerous.
DO NOT
drop or bump the tyre inflator.
DO NOT
get the tyre inflator wet.
DO NOT
operate near appliances with strong magnetic fields, corrosive gasses or corrosive liquids.
composite body with backlit lcd digital display and rubber protector. select between bar, psi, kg/cm² or kPa. supplied with 200mm rubber hose
and push-on connector. Powered by 2 x cr2032 batteries (supplied).
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA393
range:. . . . . . . . . 5-150psi(0.344-10.34bar, 0.35-10.55kg/cm², 34.5-1034kPa)
Pressure units:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . psi, bar, kg/cm², kPa
Air supply maximum:. . . . . . . . . . . . 150psi, 10.34bar, 10.55kg/cm², 1034kPa
Inlet size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4"BsP
Batteries (lithium button cell):. . . . . . . . . . . . . . . . . . . . 2 x cr2032 (supplied)
4.1.
AIR SUPPLY
recommended hook-up is shown in fig.1. (to avoid possible damage to the gauge see note in fig.1 *
IMPORTANT!
)
WARNING!
ensure the air supply is clean and dry. A suitable filter/water trap will be required in the supply line.
4.1.1.
An air line pressure up to 150psi can be delivered to the tyre inflator. Please note the maximum available pressure cannot exceed the
supply pressure.
4.1.2. drain the air tank daily. Water in the air line must be kept to a minimum.
4.1.3. clean the air inlet filter weekly.
4.1.4. the minimum hose diameter should be 1/4” I.d. and fittings must have the same inside dimensions.
4.1.5.
Keep hoses away from heat, oil and sharp edges. check hoses for wear, and make certain that all connections are secure.
fig.1
(150psi max)
TWIN PUSH ON
CONNECTOR
SA393
5.1
To Inflate
5.1.1.
Be aware of the tyre pressure requirement for the vehicle.
5.1.2. switch on (fig.2) the tyre inflator and the lcd will display zero. Press and hold the "on_unIt" icon to select the units, then release.
5.1.3.
Push and hold the tyre inflator connector on to the tyre valve using the most convenient side of the twin valve connector.
Note! Always turn on the gauge before connecting to the tyre valve.
5.1.4.
depress the operating lever fully, momentarily and release to display the tyre pressure.
5.1.5. depress the operating lever for an appropriate period. release the lever frequently to check the pressure avoiding over inflation.
5.2.
To Deflate
5.2.1.
Push and hold the tyre inflator connector on to the tyre valve using the most convenient side of the twin valve connector.
5.2.2. depress the operating lever partially until air can be heard escaping. Hold for an appropriate period. Fully depress the operating lever
momentarily, then release to display new pressure.
IMPORTANT! Always fully depress the operating lever momentarily and release before reading the tyre pressure. If the gauge
switches off whilst attached to the tyre valve, remove the inflator from the valve before switching back on again.
*IMPORTANT!
Hold with spanner when tightening fitting.
