INSTRUCTIONS FOR
AIR/HYDRAULIC RIVETER HEAVY-DUTY
VACUUM
SYSTEM
MODEL NO:
SA316.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
R
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
Familiarise yourself with this product’s application and limitations, as well as the potential hazards peculiar to the riveter.
R
WARNING!
Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the riveter in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
Keep the riveter clean for best and safest performance.
R
WARNING!
Always wear approved eye (or face) and hand protection when operating the riveter.
Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear non-slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery. Contain or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
Keep the riveter away from your body and at a safe distance from others.
Keep children and unauthorised persons away from the working area.
Secure non stable workpieces with a clamp, vice or other adequate holding device.
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
R
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure:85-90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
Avoid unintentional starting.
DO NOT
use the riveter for a task it is not designed to perform.
DO NOT
operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT
carry by the hose, or pull the hose from the air supply.
DO NOT
get the riveter wet or use in damp or wet locations or areas where there is condensation.
DO NOT
allow untrained persons to operate the riveter.
DO NOT
operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
direct air from the air hose at yourself or others.
When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
P
owerful, extra heavy-duty tool suitable for aluminium, steel, stainless steel rivets and structural rivets from 3/16” to 1/4”. Trigger operated
riveter with hardened steel jaw assembly and air-actuated vacuum rivet shaft collector. Resilient grip for added comfort and hanging loop for
use with balancer. Supplied with three riveting nozzles, two spanners and oil can.
3. SPECIFICATIONS
Model no: ..............................................................SA316.V3
Nozzle sizes: ........
3/16”(4.8mm), 7/32”(5.6mm), 1/4”(6.4mm)
Air consumption: ............................................................
4cfm
Operating pressure: ......................................................
90psi
Air inlet size:..............................................................
1/4”BSP
Weight: ..........................................................................
1.9kg
Noise power: .............................................................
82dD(A)
Noise pressure: .........................................................
71dB(A)
V
ibration figure:
..........................................................
0.5m/s²
Uncertainty: ..............................................................
0.54m/s²
Refer to
Instructions
Wear Eye
Protection
S
A316.V3 | Issue 1 12/05/15
Original Language Version
© Jack Sealey Limited
