Ensure you have read understood and follow the safety instructions in Section 1.
4.1. Attach the retaining spring by holding the front end of the spring and screwing it onto the gun retainer.
4.2. Insert the chisel using the spring’s hooked end to hold the chisel in place.
4.3. Attached the tool to the air supply as mentioned in Section 2.
4.4. to operate the hammer, squeeze the trigger.
NOTE: The air regulator may be used as a means of throttle control.
Chisel: Available from your authorised Sealey Dealer. Part No: SA120/P - Pointed SA120/F - Flat.
WARNING!
Disconnect the hammer from the air supply before changing accessories, servicing or performing any maintenance.
5.1 Keep the hammer oiled for optimum performance
lubricate daily with a good grade of air oil such as Sealey Ato/500 or Ato/1000. If no air tool oiler is used, a teaspoon of oil can be
poured into the tool’s air inlet, or into the hose at the nearest connection to the air supply. then run the hammer for a short time.
5.2. When not in use, always turn off air supply.
Note:
the following external factors may cause loss of power and effect hammer performance:
the air system.
Reduced compressor output, excessive drain on the air line, moisture or restrictions in air pipes or in the use of hose connection
having the improper size. Correct the condition accordingly.
the tool
Grit or gum deposits in the tool. Correct by cleaning the air stainer,if present, and flushing out the tool with gum solvent oil or an equal
mixture of
SAE no.10 oil and kerosene.
If despite taking action as for above situations the tool function is impaired, contact your local Sealey service dealer for advice.
Chisel Shank Size . . . . . . 12.7 x 47mm
Speed . . . . . . . . . . . . . . . . . . . 3000bpm
Air Consumption. . . . . . . . . . . . . . 4cfm
operating Pressure . . . . . . . . . . . 90psi
Air Inlet Size . . . . . . . . . . . . . . .1/4”BSP
Piston Stroke . . . . . . . . . . . . . . . 20mm
Vibration . . . . . . . . . . . . . . . . 20.88m/s²
Uncertainty . . . . . . . . . . . . . . . 3.06m/s²
noise Power . . . . . . . . . . . . . .114.04dB
noise Pressure. . . . . . . . . . . . .103.5dB
3. sPeCIFICATION
4. OPeRATION
5. mAINTeNANCe
environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Weee Regulations
Dispose of this product at the end of its working life in compliance with the eU Directive on
Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImPORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORmATION:
for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sole UK Distributor, sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Original Language Version
© Jack Sealey limited
SA120.V2 Issue: 3(SP) - 28/04/14
