4. OPERATION
4.1.
CHARGING THE UNIT
NOTE:
Ensure unit is fully charged before first use.
4.1.1.
Connect unit to power source using the Micro USB cable or
USB C cable.
4.1.2.
Press On/Off button to turn on the unit. Charge indicator
lights will flash while charging and fully lit once fully charged.
4.1.3.
Unplug cable when fully charged.
4.2.
CHARGING EXTERNAL DEVICES
4.2.1.
Connect the unit to the external device via the USB cable.
4.2.2.
Press On/Off button to turn on the unit.
4.2.3.
Turn unit off and disconnect cable when external device is
fully charged.
4.3.
LED TORCH/FLASHLIGHT
4.3.1.
Press and hold the On/Off button for approximately 3 seconds to turn
the torch on constantly.
4.3.2.
To cycle through settings, press once more for S.O.S. flash, once more for
constant flash and once more for Off.
4.4.
JUMP STARTING
NOTE:
Before attempting to start your vehicle, ensure that at least 3 of
the 4 Charge Indicator lights are lit.
NOTE:
When the Jump Start Connector is connected to the unit,
DO NOT
allow the battery clamps to touch each other.
4.4.1.
Insert Jump Start Connector into the unit and connect the battery clamps to the battery terminals.
4.4.2.
The Clamp Indicator LED will flash red and green indicating it is safe to proceed.
NOTE:
If only the red Clamp Indicator LED is lit, the Clamps may be connected in reverse. Reverse connections.
4.4.3.
If the engine does not start, disconnect the Clamps, wait for 30 seconds and try again.
4.4.4.
After 3 attempts, it is possible to use the Force Start function as described below.
4.4.5.
Force Start method: Connect the clamps to the battery terminals and hold the Force Start Button down for 3 seconds. If the
indicator light of the Clamp is solid green, you need to start the vehicle within 30 seconds.
4.4.6.
Once started, remove the unit from the battery.
5. TROUBLESHOOTING
6. MAINTENANCE
6.1.
After use and before performing cleaning, unplug and disconnect the unit.
6.2.
Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clamps, cords, and the outer case.
Original Language Version
© Jack Sealey Limited
Item no.
Description
1
O
n / Off Button
2
Charge Indicator LEDs
3
LED Torch / Flashlight
4
U
SB Output Port 1 (QC 3.0)
5
U
SB Output Port 2 (QC 3.0)
6
U
SB C Input & Output (PD30W)
7
M
icro USB Input Port (Charging)
8
J
ump Start Port
9
Negative (Black) Clamp
10
P
ositive (Red) Clamp
11
Jump Start Connector
12
Clamp Indicator Light
13
Force Start Button
LED State
Status
T
he red/green light will flash
Ready to work
The red light is always on
1. Battery clamp is reverse connected.
-Check whether the clamp is reverse connected. Correct if required.
2. The clamp is short-circuited.
-Check whether two clamps are touching or connected to the same metal surface.
The red light is always on
Reverse charging protection, the voltage of the car battery is higher than 12.6V.
-No jump starter needed, the car battery is enough to start your car.
T
he red light flashes quickly
The temperature of the clamp exceeds 65(+/-5) degrees.
-Remove the clamp until the red/green light flashes.
T
he green light flashes slowly
The voltage of the jump starter is too low.
-Recharge unit.
RS1200 Issue:1 06/06/22
