background image

 

1. IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS 
This manual contains important safety and operating instructions. 

 
RISK OF ELECTRIC SHOCK OR FIRE. 
 
 
 

1.1.

 

Read the entire manual before using this product. Failure to do so could result in serious injury  
or death. 

1.2. Keep out of reach of children. 
1.3. This Roadstart

®

 is not intended for use by persons (including children) with reduced physical,  

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction concerning the use of the Roadstart® by a person responsible for their 
safety. 

1.4. Do not put fingers or hands into the product. 
1.5. Do not expose the booster to rain or snow. 
1.6.  Use  only  recommended  attachments.  Use  of  an  attachment  not  recommended  or  sold  by  
       

 

the manufacturer may result in a risk of fire, electric shock or injury to persons or 

 

damage to property. 

1.7. To reduce the risk of damage to the electric plug or cord, pull by the plug rather than the cord  
        when disconnecting the Roadstart®. 
1.8. To reduce the risk of electric shock, unplug the Roadstart® charger from the outlet before  
 

attempting any maintenance or cleaning. Simply turning off the controls will not reduce this risk. 

1.9. Do not operate the Roadstart® or charger with a damaged output cable; have the damaged part  
        replaced immediately by a qualified service person. 
1.10. Do not operate the Roadstart® if it has received a sharp blow, been dropped or otherwise 

damaged in any way; take it to a qualified service person. 

1.11. Do not disassemble the Roadstart® or charger; take it to a qualified service person when service 
or repair is required. Incorrect reassembly may result in a risk of fire or electric shock. 
 
 

RISK OF EXPLOSIVE GASES. PREVENT FLAMES AND SPARKS. 
PROVIDE ADEQUATE VENTILATION DURING CHARGING. 
1.12.  
WORKING  IN  THE  VICINITY  OF  A  LEAD-ACID  BATTERY  IS  DANGEROUS.  BATTERIES 
GENERATE  EXPLOSIVE  GASES  DURING  NORMAL  OPERATION.  FOR  THIS  REASON,  IT  IS 
IMPORTANT  THAT  YOU  FOLLOW  THESE  INSTRUCTIONS  EACH  TIME  YOU  USE  THE 

ROADSTART®. 

1.13. The Roadstart® and lead-acid battery of the vehicle must be placed in a well-ventilated area. 
1.14. To reduce the risk of a battery explosion, follow these instructions and those published by the  
           battery manufacturer and the manufacturer of any equipment you intend to use in the vicinity  
          of the battery. Review the cautionary markings on these products and on the engine. 
1.15. This Roadstart® employs parts, such as switches and circuit breakers, that tend to produce arcs  
 

and sparks. If used in a garage, locate this Roadstart® 46 cm or move above floor level. 

 

Do  not  use  with  non-rechargeable  batteries.  Use  only  with  lead-acid  type 
rechargeable batteries. 

 
 
 
 

/!\   WARNING  

Summary of Contents for ROADSTART PBI2212GS
















Reviews: