5.1
Maintenance and repair of the jack may only be carried out by
personnel qualified in the servicing of hydraulic systems.
should your jack be defective or you suspect the jack to be
damaged or in any way unsafe, remove from service
immediately and contact your authorised sealey dealer for
advice and repairs.
5.2
When the jack is not in use, keep the ram fully retracted and
the release valve closed.
5.3
clean the jack regularly and oil/grease all pivoting sections
every 3 months (more often if using jack in extremely dry/dusty
conditions)
5.4
frequently check hydraulic oil level (see section 3.2). never
top up the hydraulic system with brake fluid. use hydraulic jack
oil only. IMPortAnt. overfilling the jack may render it
inoperative.
5.5
check the piston and piston rod periodically for signs of rust/
corrosion.
declaration of Conformity
We, the sole importer into the uK, declare that the product listed below is in conformity with the following standards and directives
the construction files for this product is held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack sealey Ltd
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Trolley Jack
model no: TJ3.v3
2006/42/Ec Machinery Directive
93/68/EEc cE Marking Directive
2nd April 2008
signed by Mark sweetman
01284 757500
01284 703534
sole uK distributor
sealey group,
Bury st. Edmunds, suffolk.
www.sealey.co.uk
Web
notE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
impORTAnT:
no liability is accepted for incorrect use of this product.
WARRAnTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
infORmATiOn:
for a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
6. TROubLEshOOTing
ProBLEM
cAusE
soLutIon
Jack does not lift.
1. release valve is open.
2. Low or no hydraulic fluid in reservoir.
3. Air locked system.
4. overload valve has operated.
5. Delivery valve and/or bypass valve malfunctioning.
6. Packing worn out or defective.
1. Verify the release valve is closed by the position of the handle.
release valve may need cleaning.
2. fill with sealey hydraulic oil and bleed system.
3. Bleed system.
4. use appropriate higher rated jack.
5. clean jack to remove dirt and foreign matter. replace hydraulic oil.
6. replace packing.
Jack will not lift all the way.
1. too much or not enough hydraulic oil.
1. check hydraulic oil level.
Jack will only lift slowly.
1. Pump not working correctly.
2. Leaking seals.
1. renovate pump.
2. replace seals.
Jack lifts load but
will not hold it.
1. cylinder packing is leaking.
2. Valve not working correctly (suction, delivery,
delivery, release or bypass).
3. Air locked system.
1. replace packing.
2. Inspect valves, replace if necessary.
3. Bleed system.
Jack leaks hydraulic fluid.
1. Worn or damaged seals.
1. replace seals.
Jack will not retract.
1. release valve is closed.
1. open the release valve by pulling on and turning the handle clockwise
May be necessary to clean release valve.
Jack retracts only slowly.
1. cylinder damaged internally.
2. return spring(s) damaged.
3. Link section is binding.
1. return jack to authorised service centre.
2. replace return spring(s).
3. Lubricate link sections.
5. mAinTEnAnCE
4.1.7 Position suitably rated axle stands beneath the vehicle and
lower the jack slightly so that the weight is taken by the axle
stands and not the jack.
4.2
Lowering
raise the jack a small amount to free the axle
stands and remove them.
4.2.1 Before lowering the jack, be sure that the area beneath the
vehicle is clear of any persons/obstructions.
sLOWLY
open the release valve by lifting and rotating the
handle clockwise. Hold the handle in this position until the jack
is fully lowered. release the handle to allow it to automatically
return to its original position.
4.2.2 the jack is fitted with a safety device that ensures smooth and
uniform lowering.
4.2.3 When the lifting arm is in its lowest position, remove the jack
from under the vehicle.
5.6
following a period of prolonged intensive use the hydraulic oil
should be completely changed. remove the filler plug and
drain all the oil from the jack into a suitable container.
refill with sealey hydraulic oil using the exact quantity stated
below.
Oil capacity: TJ3 - 0.41 ltr
tJ3.V3 Issue no: 1 - 02/04/08