background image

POWERMIG

WELDERS

POWERMIG2750.V2

POWERMIG3500.V2

POWERMIG4500.V2

Environmental Protection.

 

   

Recycle unwanted materials instead of disposing of them as waste.  All tools, accessories and packaging  

 

   

should be sorted, taken to a recycle centre and disposed of in a manner which is compatible with the  

 

   

environment.

 

 

 

   

WEEE REGULATIONS. 

Dispose of this product at the end of its working life in compliance with the EU  

 

   

Directive on Waste Electrical and Electronic Equipment. When the product is no longer required, it must be  

 

   

disposed of in an environmentally protective way. 

NOTE:

 It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION:

 For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group, 

Kempson Way, Suffolk Business Park

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

email

Original Language Version

POWERMIG2750.V2, POWERMIG3500.V2, POWERMIG4500.V2    Issue: 3 - 09/04/10

Summary of Contents for POWERMIG2750.V2













Reviews: