Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
3
Follow all workshop health & safety rules, regulations, and conditions when using drill.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the
drill in good condition and replace any damaged or worn parts.
Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
p
WARNING!
Check correct air pressure is maintained and not exceeded. We recommended 90 psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use
and ensure that all connections are secure.
3
Wear approved safety eye protection. If dust is generated wear respiratory protection, and
safety gloves.
3
Wear suitable clothing to avoid snagging.
DO NOT
wear loose jewellery and tie back long hair.
3
Keep hands away from rotating chuck and drill bit.
3
Keep drill bits clean and sharp for best and safest performance.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non stable work piece with a clamp, vice or other adequate holding device.
3
Ensure the chuck is securely fastened to the spindle and the drill bit is secure in the chuck.
3
Keep children and unauthorised persons away from the working area.
8
DO NOT
get the drill wet or use in damp or wet locations.
8
DO NOT
apply excessive loads to the drill bit during operation.
8
DO NOT
hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
7
DO NOT
use the drill for a task it is not designed to perform.
p
WARNING! DO NOT
use drill if damaged or faulty. Contact your local service agent.
p
WARNING!
Beware of high-reaction torque when breaking through the material being drilled.
7
DO NOT
use drill unless you have been instructed in its use by a qualified person.
7
DO NOT
drop, throw or abuse the drill.
7
DO NOT
carry the drill by the air hose, or yank the hose from the air supply.
7
DO NOT
operate drill if you are tired, under the influence of alcohol, drugs or intoxicating
medication.
7
DO NOT
carry drill with your hand on the power trigger in order to avoid unintentional starting.
7
DO NOT
direct air from the air hose at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2.
INTRODUCTION & SPECIFICATIONS
Chuck size . . . . . . . . . . . . . . . . . 10mm
Free speed . . . . . . . . . . . . . . . 1800rpm
Air consumption . . . . . . . . . . . . . . .4cfm
Operating pressure. . . . . . . . . . . . 90psi
Air inlet size . . . . . . . . . . . . . . 1/4”BSP
Weight . . . . . . . . . . . . . . . . . . . . 1.15kg
Noise Power . . . . . . . . . . . . . . . .83dB.A
Composite lightweight moulded housing reduces effects of chill on operator’s hands. Fully
reversible with thumb control set above motor housing. Air motor with quality bearings for smooth
powerful operation. Handle exhaust with built in muffler reduces noise level. Fitted with Jacob’s
keyless chuck for fast bit changes. Suitable for the professional workshop.
Original Language Version
SA620.V2 Issue: 1 - 08/09/11
INSTRUCTIONS FOR:
AIR PISTOL DRILL
COMPOSITE PREMIER
MODEL No:
SA620.V2
