background image

 8.  OPTIONAL HOSE REEL KIT - PCHOSE  

NOTE:

 It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts 

without prior notice.

IMPORTANT: 

No responsibility is accepted for incorrect use of this equipment.

WARRANTY: 

Guarantee is 12 months from purchase, proof of which will be required for any claim.

INFORMATION: 

For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including 

postcode.

8.1. 

Fitting the hose reel kit.

 To fit the hose reel kit undo the four screws holding the rear cover panel in place and remove the panel.  

 

(See fig.13). 

8.2.

 

Place the hose reel assembly with its supports onto the main casing as shown in fig.20. Use the same four screws to retain the  

 

hose reel on the same fixing points as the rear cover.

8.3.

 

Attach the end of the gun hose to the fitting within the reel (See fig.20) then wind the handle in the direction shown whilst guiding  

 

the hose neatly onto the reel.

8.4.

 

Connect the feeder hose from the centre of the reel (opposite the handle) to the outlet fitting at the base of the unit as shown in  

 

fig.21.

8.0. 

Optional extras include the following:-

 

Hose reel kit,   . . . . . . . . . . . . . . . . . . . . . . . Model No. PCHOSE, 

 

Rotary brush for patio cleaning,  . . . . . . . . . Model No. PCPATIO, 

 

Drain kit,  . . . . . . . . . . . . . . . . . . . . . . . . . . . Model No. AK127/F, 

  

Rotary brush,  . . . . . . . . . . . . . . . . . . . . . . . Model No. AK125/F.   

01284 757500
01284 703534

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

[email protected]

email

Original Language Version

PC3455    Issue No.2 19/08/10

Summary of Contents for PC3455.V2








Reviews: